X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2FAP1000.h;h=fd074fb5cee15f9454fc013a72bd3eb5b9aa1352;hb=10d1a160f5e28b05f891c050ca2f23855b226f5f;hp=ec982bdc51218725a0aa9aec1919754152b57414;hpb=f61f1e150c84f5b9347fca79a4bc5f2286c545d2;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h
index ec982bd..fd074fb 100644
--- a/include/configs/AP1000.h
+++ b/include/configs/AP1000.h
@@ -27,6 +27,14 @@
 
 #define CONFIG_AP1000	1		/* ...on an AP1000 board    */
 
+/*
+ * Start at bottom of RAM, but at an aliased address so that it looks
+ * like it's not in RAM.  This is a bit of voodoo to allow it to be
+ * run from RAM instead of Flash.
+ */
+#define	CONFIG_SYS_TEXT_BASE	0x08000000
+#define CONFIG_SYS_LDSCRIPT	"board/amirix/ap1000/u-boot.lds"
+
 #define CONFIG_PCI	1
 
 #define CONFIG_SYS_HUSH_PARSER 1		/* use "hush" command parser	*/
@@ -34,7 +42,6 @@
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 
 #define CONFIG_COMMAND_EDIT	1
-#define CONFIG_COMMAND_HISTORY	1
 #define CONFIG_COMPLETE_ADDRESSES 1
 
 #define CONFIG_ENV_IS_IN_FLASH	1
@@ -53,12 +60,6 @@
 
 #define CONFIG_BOOTCOMMAND	""	/* autoboot command */
 
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
-
 #define CONFIG_BOOTARGS		"console=ttyS0,57600"
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
@@ -94,6 +95,14 @@
 #define CONFIG_SPD_EEPROM	1	/* use SPD EEPROM for setup    */
 
 /*
+ * I2C
+ */
+#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
+#define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_SPEED	400000
+
+/*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
@@ -148,7 +157,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0x20000000
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
 
@@ -209,9 +218,8 @@
  */
 
 #define CONFIG_SYS_INIT_RAM_ADDR	0x400000  /* inside of SDRAM			 */
-#define CONFIG_SYS_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in RAM	       */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -220,14 +228,6 @@
  */
 #define SPD_EEPROM_ADDRESS	0x50
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot		*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
@@ -239,7 +239,6 @@
 #define CONFIG_SYS_JFFS2_NUM_BANKS	1
 #define CONFIG_SYS_JFFS2_FIRST_SECTOR	1
 
-#define CONFIG_NET_MULTI
 #define CONFIG_E1000
 
 #define CONFIG_SYS_ETH_DEV_FN		0x0800