X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fcommproc.h;h=52ac4caf5a4fd7a25e915aa264932855341f760e;hb=906f609681bdf8341fbf313ee2455a4f56906f08;hp=6959905efe8f1665561f699b6cd71b925577ab58;hpb=3be2bdf5dc69b3142c1162a59bc67191c9077567;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/commproc.h b/include/commproc.h index 6959905..52ac4ca 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -12,15 +12,10 @@ * CPM capabilities. I (or someone else) will add definitions as they * are needed. -- Dan * - * On the MBX board, EPPC-Bug loads CPM microcode into the first 512 - * bytes of the DP RAM and relocates the I2C parameter area to the - * IDMA1 space. The remaining DP RAM is available for buffer descriptors - * or other use. */ #ifndef __CPM_8XX__ #define __CPM_8XX__ -#include #include /* CPM Command register. @@ -136,7 +131,6 @@ typedef struct cpm_buf_desc { #define PROFF_SMC2 ((uint)0x0380) /* Define enough so I can at least use the serial port as a UART. - * The MBX uses SMC1 as the host serial port. */ typedef struct smc_uart { ushort smc_rbase; /* Rx Buffer descriptor base address */ @@ -435,38 +429,6 @@ typedef struct scc_enet { * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers. **********************************************************************/ - -/*** ADS *************************************************************/ - -#if defined(CONFIG_MPC860) && defined(CONFIG_ADS) -/* This ENET stuff is for the MPC860ADS with ethernet on SCC1. - */ - -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 - -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00001000) - -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000002c) - -/* 68160 PHY control */ - -#define PC_ENET_ETHLOOP ((ushort)0x0800) -#define PC_ENET_TPFLDL ((ushort)0x0400) -#define PC_ENET_TPSQEL ((ushort)0x0200) - -#endif /* MPC860ADS */ - /*** BSEIP **********************************************************/ #ifdef CONFIG_BSEIP @@ -569,101 +531,6 @@ typedef struct scc_enet { #endif -/*** FADS823 ********************************************************/ - -#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS) -/* This ENET stuff is for the MPC823FADS with ethernet on SCC2. - */ -#ifdef CONFIG_SCC2_ENET -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define CPMVEC_ENET CPMVEC_SCC2 -#endif - -#ifdef CONFIG_SCC1_ENET -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define CPMVEC_ENET CPMVEC_SCC1 -#endif - -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0400) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00002000) - -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) - -#endif /* CONFIG_FADS823FADS */ - -/*** FADS850SAR ********************************************************/ - -#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS) -/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of - * this may be unique to the FADS850SAR configuration. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */ -#endif /* CONFIG_FADS850SAR */ - -/*** FADS860T********************************************************/ - -#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x) -/* - * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1. - */ -#ifdef CONFIG_SCC1_ENET - -#define SCC_ENET 0 - -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 - -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00001000) - -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000002c) - -#endif /* CONFIG_SCC1_ETHERNET */ - -/* - * This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS - * with ethernet on FEC. - */ - -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* Use FEC for Ethernet */ -#endif /* CONFIG_FEC_ENET */ - -#endif /* CONFIG_FADS && CONFIG_MPC86x */ - /*** FPS850L, FPS860L ************************************************/ #if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L) @@ -710,32 +577,6 @@ typedef struct scc_enet { #define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */ #endif /* CONFIG_GEN860T */ -/*** GENIETV ********************************************************/ - -#if defined(CONFIG_GENIETV) -/* Ethernet is only on SCC2 */ - -#define CONFIG_SCC2_ENET -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define CPMVEC_ENET CPMVEC_SCC2 - -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) - -#endif /* CONFIG_GENIETV */ - /*** HERMES-PRO ******************************************************/ /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ @@ -889,60 +730,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00003E00) #endif /* CONFIG_LWMON */ -/*** NX823 ***********************************************/ - -#if defined(CONFIG_NX823) -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002f00) - -#endif /* CONFIG_NX823 */ - -/*** MBX ************************************************************/ - -#ifdef CONFIG_MBX -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. The TCLK and RCLK seem unique - * to the MBX860 board. Any two of the four available clocks could be - * used, and the MPC860 cookbook manual has an example using different - * clock pins. - */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0200) -#define PA_ENET_RCLK ((ushort)0x0800) -#define PC_ENET_TENA ((ushort)0x0001) -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000003d) -#endif /* CONFIG_MBX */ - /*** KM8XX *********************************************************/ /* The KM8XX Service Module uses SCC3 for Ethernet */ @@ -1074,121 +861,6 @@ typedef struct scc_enet { #endif /* CONFIG_NETVIA */ -/*** QS850/QS823 ***************************************************/ - -#if defined(CONFIG_QS850) || defined(CONFIG_QS823) -#undef FEC_ENET /* Don't use FEC for EThernet */ - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 - -#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */ -#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */ -#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */ -#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */ -#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */ -#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */ -#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */ -#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */ -#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */ -#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */ - -/* SCC2 TXCLK from CLK2 - * SCC2 RXCLK from CLK4 - * SCC2 Connected to NMSI */ -#define SICR_ENET_MASK ((uint)0x00007F00) -#define SICR_ENET_CLKRT ((uint)0x00003D00) - -#endif /* CONFIG_QS850/QS823 */ - -/*** QS860T ***************************************************/ - -#ifdef CONFIG_QS860T -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* use FEC for EThernet */ -#endif /* CONFIG_FEC_ETHERNET */ - -/* This ENET stuff is for GTH 10 Mbit ( SCC ) */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 - -#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */ -#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */ -#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */ -#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */ -#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */ - -#define SICR_ENET_MASK ((uint)0x000000ff) -/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */ -#define SICR_ENET_CLKRT ((uint)0x0000003D) - -#endif /* CONFIG_QS860T */ - -/*** RPXCLASSIC *****************************************************/ - -#ifdef CONFIG_RPXCLASSIC - -#ifdef CONFIG_FEC_ENET - -# define FEC_ENET /* use FEC for EThernet */ -# undef SCC_ENET - -#else /* ! CONFIG_FEC_ENET */ - -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. - */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0200) -#define PA_ENET_RCLK ((ushort)0x0800) -#define PB_ENET_TENA ((uint)0x00001000) -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000003d) - -#endif /* CONFIG_FEC_ENET */ - -#endif /* CONFIG_RPXCLASSIC */ - -/*** RPXLITE ********************************************************/ - -#ifdef CONFIG_RPXLITE -/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of - * this may be unique to the RPX-Lite configuration. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0200) -#define PA_ENET_RCLK ((ushort)0x0800) -#if defined(CONFIG_RMU) -#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */ -#else -#define PB_ENET_TENA ((uint)0x00002000) -#endif -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003d00) -#endif /* CONFIG_RPXLITE */ - /*** SM850 *********************************************************/ /* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */ @@ -1257,7 +929,7 @@ typedef struct scc_enet { /*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/ #if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \ - defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \ + defined(CONFIG_R360MPI) || \ defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \ defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \ defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \ @@ -1351,29 +1023,6 @@ typedef struct scc_enet { # endif /* CONFIG_FEC_ENET */ #endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */ -/*** V37 **********************************************************/ - -#ifdef CONFIG_V37 -/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of - * this may be unique to the Marel V37 configuration. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0400) -#define PA_ENET_RCLK ((ushort)0x0200) -#define PB_ENET_TENA ((uint)0x00002000) -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) -#endif /* CONFIG_V37 */ - - /*********************************************************************/ /* SCC Event register as used by Ethernet.