X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=drivers%2Fpower%2FKconfig;h=26257a72bc699fe0899a25b3eec1994618f02f03;hb=b4c2c151b14b59a2403675526adf666710cade67;hp=a7d56e605d722a7761517cb3c2656d67c2a738a1;hpb=102d86552abc82818c22b39fdef4b3a280a60643;p=platform%2Fkernel%2Fu-boot.git

diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index a7d56e6..26257a7 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -1,5 +1,7 @@
 menu "Power"
 
+source "drivers/power/acpi_pmc/Kconfig"
+
 source "drivers/power/domain/Kconfig"
 
 source "drivers/power/pmic/Kconfig"
@@ -11,8 +13,9 @@ choice
 	depends on ARCH_SUNXI
 	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
 	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
+	default AXP305_POWER if MACH_SUN50I_H616
 	default AXP818_POWER if MACH_SUN8I_A83T
-	default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
+	default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_V3S
 
 config SUNXI_NO_PMIC
 	bool "board without a pmic"
@@ -22,6 +25,7 @@ config SUNXI_NO_PMIC
 config AXP152_POWER
 	bool "axp152 pmic support"
 	depends on MACH_SUN5I
+	select AXP_PMIC_BUS
 	select CMD_POWEROFF
 	---help---
 	Select this to enable support for the axp152 pmic found on most
@@ -29,7 +33,8 @@ config AXP152_POWER
 
 config AXP209_POWER
 	bool "axp209 pmic support"
-	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_V3S
+	select AXP_PMIC_BUS
 	select CMD_POWEROFF
 	---help---
 	Select this to enable support for the axp209 pmic found on most
@@ -38,14 +43,25 @@ config AXP209_POWER
 config AXP221_POWER
 	bool "axp221 / axp223 pmic support"
 	depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
+	select AXP_PMIC_BUS
 	select CMD_POWEROFF
 	---help---
 	Select this to enable support for the axp221/axp223 pmic found on most
 	A23 and A31 boards.
 
+config AXP305_POWER
+	bool "axp305 pmic support"
+	depends on MACH_SUN50I_H616
+	select AXP_PMIC_BUS
+	select CMD_POWEROFF
+	---help---
+	Select this to enable support for the axp305 pmic found on most
+	H616 boards.
+
 config AXP809_POWER
 	bool "axp809 pmic support"
 	depends on MACH_SUN9I
+	select AXP_PMIC_BUS
 	select CMD_POWEROFF
 	---help---
 	Say y here to enable support for the axp809 pmic found on A80 boards.
@@ -53,6 +69,7 @@ config AXP809_POWER
 config AXP818_POWER
 	bool "axp818 pmic support"
 	depends on MACH_SUN8I_A83T
+	select AXP_PMIC_BUS
 	select CMD_POWEROFF
 	---help---
 	Say y here to enable support for the axp818 pmic found on
@@ -120,11 +137,12 @@ config AXP_DCDC3_VOLT
 
 config AXP_DCDC4_VOLT
 	int "axp pmic dcdc4 voltage"
-	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP305_POWER
 	default 1250 if AXP152_POWER
 	default 1200 if MACH_SUN6I
 	default 0 if MACH_SUN8I
 	default 900 if MACH_SUN9I
+	default 1500 if AXP305_POWER
 	---help---
 	Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
 	disable dcdc4.
@@ -133,6 +151,7 @@ config AXP_DCDC4_VOLT
 	On A23 / A33 boards dcdc4 is unused and should be disabled.
 	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
 	On A83T boards dcdc4 is used for VDD-GPU.
+	On H616 boards dcdcd is used for VCC-DRAM.
 
 config AXP_DCDC5_VOLT
 	int "axp pmic dcdc5 voltage"
@@ -192,6 +211,48 @@ config AXP_ALDO3_VOLT
 	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
 	3.0V.
 
+choice
+	prompt "axp pmic (a)ldo3 voltage rate control"
+	depends on AXP209_POWER
+	default AXP_ALDO3_VOLT_SLOPE_NONE
+	---help---
+	The AXP can slowly ramp up voltage to reduce the inrush current when
+	changing voltages.
+	Note, this does not apply when enabling/disabling LDO3. See
+	"axp pmic (a)ldo3 inrush quirk" below to enable a slew rate to limit
+	inrush current on broken board designs.
+
+config AXP_ALDO3_VOLT_SLOPE_NONE
+	bool "No voltage slope"
+	---help---
+	Tries to reach the next voltage setting near instantaneously. Measurements
+	indicate that this is about 0.0167 V/uS.
+
+config AXP_ALDO3_VOLT_SLOPE_16
+	bool "1.6 mV per uS"
+	---help---
+	Increases the voltage by 1.6 mV per uS until the final voltage has
+	been reached. Note that the scaling is in 25 mV steps and thus
+	the slew rate in reality is about 25 mV/31.250 uS.
+
+config AXP_ALDO3_VOLT_SLOPE_08
+	bool "0.8 mV per uS"
+	---help---
+	Increases the voltage by 0.8 mV per uS until the final voltage has
+	been reached. Note that the scaling is in 25 mV steps however and thus
+	the slew rate in reality is about 25 mV/15.625 uS.
+	This is the slowest supported rate.
+
+endchoice
+
+config AXP_ALDO3_INRUSH_QUIRK
+	bool "axp pmic (a)ldo3 inrush quirk"
+	depends on AXP209_POWER
+	---help---
+	The reference design denotes a value of 4.7 uF for the output capacitor
+	of LDO3. Some boards have too high capacitance causing 	an inrush current
+	and resulting an AXP209 shutdown.
+
 config AXP_ALDO4_VOLT
 	int "axp pmic (a)ldo4 voltage"
 	depends on AXP209_POWER
@@ -295,7 +356,6 @@ config AXP_FLDO3_VOLT
 config AXP_SW_ON
 	bool "axp pmic sw on"
 	depends on AXP809_POWER || AXP818_POWER
-	default n
 	---help---
 	Enable to turn on axp pmic sw.
 
@@ -311,8 +371,16 @@ config SY8106A_VOUT1_VOLT
 config TWL4030_POWER
 	depends on OMAP34XX
 	bool "Enable driver for TI TWL4030 power management chip"
+	imply CMD_POWEROFF
 	---help---
 	The TWL4030 in a combination audio CODEC/power management with
 	GPIO and it is commonly used with the OMAP3 family of processors
 
+config POWER_MT6323
+	bool "Poweroff driver for mediatek mt6323"
+	select CMD_POWEROFF
+	help
+	  This adds poweroff driver for mt6323
+	  this pmic is used on mt7623 / Bananapi R2
+
 endmenu