X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=drivers%2Fmtd%2Fnand%2Fomap_gpmc.c;h=389c4de59a1189d6cbc22f51337bab1a56ef9002;hb=13fbde6e4f600d94f0a1fb6ae49c6b4888033cec;hp=ec1787f22492d93322a4014c6acc3d3da9ba2d9f;hpb=5b9c79a81db80c3f9e50c77477957cd803429af8;p=platform%2Fkernel%2Fu-boot.git diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c index ec1787f..389c4de 100644 --- a/drivers/mtd/nand/omap_gpmc.c +++ b/drivers/mtd/nand/omap_gpmc.c @@ -15,15 +15,13 @@ #include #include #include -#ifdef CONFIG_AM33XX -#include -#endif +#include + +#define BADBLOCK_MARKER_LENGTH 2 +#define SECTOR_BYTES 512 static uint8_t cs; -static __maybe_unused struct nand_ecclayout hw_nand_oob = - GPMC_NAND_HW_ECC_LAYOUT; -static __maybe_unused struct nand_ecclayout hw_bch8_nand_oob = - GPMC_NAND_HW_BCH8_ECC_LAYOUT; +static __maybe_unused struct nand_ecclayout omap_ecclayout; /* * omap_nand_hwcontrol - Set the address pointers corretly for the @@ -233,6 +231,7 @@ struct nand_bch_priv { uint8_t type; uint8_t nibbles; struct bch_control *control; + enum omap_ecc ecc_scheme; }; /* bch types */ @@ -274,66 +273,66 @@ static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) { uint32_t val; uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; -#ifdef CONFIG_AM33XX uint32_t unused_length = 0; -#endif uint32_t wr_mode = BCH_WRAPMODE_6; struct nand_bch_priv *bch = chip->priv; /* Clear the ecc result registers, select ecc reg as 1 */ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); -#ifdef CONFIG_AM33XX - wr_mode = BCH_WRAPMODE_1; + if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) { + wr_mode = BCH_WRAPMODE_1; - switch (bch->nibbles) { - case ECC_BCH4_NIBBLES: - unused_length = 3; - break; - case ECC_BCH8_NIBBLES: - unused_length = 2; - break; - case ECC_BCH16_NIBBLES: - unused_length = 0; - break; - } + switch (bch->nibbles) { + case ECC_BCH4_NIBBLES: + unused_length = 3; + break; + case ECC_BCH8_NIBBLES: + unused_length = 2; + break; + case ECC_BCH16_NIBBLES: + unused_length = 0; + break; + } - /* - * This is ecc_size_config for ELM mode. - * Here we are using different settings for read and write access and - * also depending on BCH strength. - */ - switch (mode) { - case NAND_ECC_WRITE: - /* write access only setup eccsize1 config */ - val = ((unused_length + bch->nibbles) << 22); - break; + /* + * This is ecc_size_config for ELM mode. Here we are using + * different settings for read and write access and also + * depending on BCH strength. + */ + switch (mode) { + case NAND_ECC_WRITE: + /* write access only setup eccsize1 config */ + val = ((unused_length + bch->nibbles) << 22); + break; - case NAND_ECC_READ: - default: + case NAND_ECC_READ: + default: + /* + * by default eccsize0 selected for ecc1resultsize + * eccsize0 config. + */ + val = (bch->nibbles << 12); + /* eccsize1 config */ + val |= (unused_length << 22); + break; + } + } else { /* - * by default eccsize0 selected for ecc1resultsize - * eccsize0 config. + * This ecc_size_config setting is for BCH sw library. + * + * Note: we only support BCH8 currently with BCH sw library! + * Should be really easy to adobt to BCH4, however some omap3 + * have flaws with BCH4. + * + * Here we are using wrapping mode 6 both for reading and + * writing, with: + * size0 = 0 (no additional protected byte in spare area) + * size1 = 32 (skip 32 nibbles = 16 bytes per sector in + * spare area) */ - val = (bch->nibbles << 12); - /* eccsize1 config */ - val |= (unused_length << 22); - break; + val = (32 << 22) | (0 << 12); } -#else - /* - * This ecc_size_config setting is for BCH sw library. - * - * Note: we only support BCH8 currently with BCH sw library! - * Should be really easy to adobt to BCH4, however some omap3 have - * flaws with BCH4. - * - * Here we are using wrapping mode 6 both for reading and writing, with: - * size0 = 0 (no additional protected byte in spare area) - * size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) - */ - val = (32 << 22) | (0 << 12); -#endif /* ecc size configuration */ writel(val, &gpmc_cfg->ecc_size_config); @@ -376,9 +375,9 @@ static void __maybe_unused omap_ecc_disable(struct mtd_info *mtd) } /* - * BCH8 support (needs ELM and thus AM33xx-only) + * BCH support using ELM module */ -#ifdef CONFIG_AM33XX +#ifdef CONFIG_NAND_OMAP_ELM /* * omap_read_bch8_result - Read BCH result for BCH8 level * @@ -631,20 +630,20 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, } return 0; } -#endif /* CONFIG_AM33XX */ +#endif /* CONFIG_NAND_OMAP_ELM */ /* * OMAP3 BCH8 support (with BCH library) */ -#ifdef CONFIG_NAND_OMAP_BCH8 +#ifdef CONFIG_BCH /* - * omap_calculate_ecc_bch - Read BCH ECC result + * omap_calculate_ecc_bch_sw - Read BCH ECC result * * @mtd: MTD device structure * @dat: The pointer to data on which ecc is computed (unused here) * @ecc: The ECC output buffer */ -static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, +static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc) { int ret = 0; @@ -689,13 +688,13 @@ static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, } /** - * omap_correct_data_bch - Decode received data and correct errors + * omap_correct_data_bch_sw - Decode received data and correct errors * @mtd: MTD device structure * @data: page data * @read_ecc: ecc read from nand flash * @calc_ecc: ecc read from HW ECC registers */ -static int omap_correct_data_bch(struct mtd_info *mtd, u_char *data, +static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data, u_char *read_ecc, u_char *calc_ecc) { int i, count; @@ -752,7 +751,162 @@ static void __maybe_unused omap_free_bch(struct mtd_info *mtd) chip_priv->control = NULL; } } -#endif /* CONFIG_NAND_OMAP_BCH8 */ +#endif /* CONFIG_BCH */ + +/** + * omap_select_ecc_scheme - configures driver for particular ecc-scheme + * @nand: NAND chip device structure + * @ecc_scheme: ecc scheme to configure + * @pagesize: number of main-area bytes per page of NAND device + * @oobsize: number of OOB/spare bytes per page of NAND device + */ +static int omap_select_ecc_scheme(struct nand_chip *nand, + enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) { + struct nand_bch_priv *bch = nand->priv; + struct nand_ecclayout *ecclayout = &omap_ecclayout; + int eccsteps = pagesize / SECTOR_BYTES; + int i; + + switch (ecc_scheme) { + case OMAP_ECC_HAM1_CODE_SW: + debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n"); + /* For this ecc-scheme, ecc.bytes, ecc.layout, ... are + * initialized in nand_scan_tail(), so just set ecc.mode */ + bch_priv.control = NULL; + bch_priv.type = 0; + nand->ecc.mode = NAND_ECC_SOFT; + nand->ecc.layout = NULL; + nand->ecc.size = 0; + bch->ecc_scheme = OMAP_ECC_HAM1_CODE_SW; + break; + + case OMAP_ECC_HAM1_CODE_HW: + debug("nand: selected OMAP_ECC_HAM1_CODE_HW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((3 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (3 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + bch_priv.control = NULL; + bch_priv.type = 0; + /* populate ecc specific fields */ + memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl)); + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 1; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 3; + nand->ecc.hwctl = omap_enable_hwecc; + nand->ecc.correct = omap_correct_data; + nand->ecc.calculate = omap_calculate_ecc; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + for (i = 0; i < ecclayout->eccbytes; i++) { + if (nand->options & NAND_BUSWIDTH_16) + ecclayout->eccpos[i] = i + 2; + else + ecclayout->eccpos[i] = i + 1; + } + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + bch->ecc_scheme = OMAP_ECC_HAM1_CODE_HW; + break; + + case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: +#ifdef CONFIG_BCH + debug("nand: selected OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((13 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (13 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + /* check if BCH S/W library can be used for error detection */ + bch_priv.control = init_bch(13, 8, 0x201b); + if (!bch_priv.control) { + printf("nand: error: could not init_bch()\n"); + return -ENODEV; + } + bch_priv.type = ECC_BCH8; + /* populate ecc specific fields */ + memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl)); + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 8; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 13; + nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.correct = omap_correct_data_bch_sw; + nand->ecc.calculate = omap_calculate_ecc_bch_sw; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH; + for (i = 1; i < ecclayout->eccbytes; i++) { + if (i % nand->ecc.bytes) + ecclayout->eccpos[i] = + ecclayout->eccpos[i - 1] + 1; + else + ecclayout->eccpos[i] = + ecclayout->eccpos[i - 1] + 2; + } + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + omap_hwecc_init_bch(nand, NAND_ECC_READ); + bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW; + break; +#else + printf("nand: error: CONFIG_BCH required for ECC\n"); + return -EINVAL; +#endif + + case OMAP_ECC_BCH8_CODE_HW: +#ifdef CONFIG_NAND_OMAP_ELM + debug("nand: selected OMAP_ECC_BCH8_CODE_HW\n"); + /* check ecc-scheme requirements before updating ecc info */ + if ((14 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) { + printf("nand: error: insufficient OOB: require=%d\n", ( + (14 * eccsteps) + BADBLOCK_MARKER_LENGTH)); + return -EINVAL; + } + /* intialize ELM for ECC error detection */ + elm_init(); + bch_priv.type = ECC_BCH8; + /* populate ecc specific fields */ + memset(&nand->ecc, 0, sizeof(struct nand_ecc_ctrl)); + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.strength = 8; + nand->ecc.size = SECTOR_BYTES; + nand->ecc.bytes = 14; + nand->ecc.hwctl = omap_enable_ecc_bch; + nand->ecc.correct = omap_correct_data_bch; + nand->ecc.calculate = omap_calculate_ecc_bch; + nand->ecc.read_page = omap_read_page_bch; + /* define ecc-layout */ + ecclayout->eccbytes = nand->ecc.bytes * eccsteps; + for (i = 0; i < ecclayout->eccbytes; i++) + ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH; + ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes - + BADBLOCK_MARKER_LENGTH; + bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW; + break; +#else + printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n"); + return -EINVAL; +#endif + + default: + debug("nand: error: ecc scheme not enabled or supported\n"); + return -EINVAL; + } + + /* nand_scan_tail() sets ham1 sw ecc; hw ecc layout is set by driver */ + if (ecc_scheme != OMAP_ECC_HAM1_CODE_SW) + nand->ecc.layout = ecclayout; + + return 0; +} #ifndef CONFIG_SPL_BUILD /* @@ -763,77 +917,46 @@ static void __maybe_unused omap_free_bch(struct mtd_info *mtd) * @eccstrength - the number of bits that could be corrected * (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16) */ -void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength) +int __maybe_unused omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength) { struct nand_chip *nand; struct mtd_info *mtd; + int err = 0; if (nand_curr_device < 0 || nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE || !nand_info[nand_curr_device].name) { - printf("Error: Can't switch ecc, no devices available\n"); - return; + printf("nand: error: no NAND devices found\n"); + return -ENODEV; } mtd = &nand_info[nand_curr_device]; nand = mtd->priv; - nand->options |= NAND_OWN_BUFFERS; - - /* Reset ecc interface */ - nand->ecc.mode = NAND_ECC_NONE; - nand->ecc.read_page = NULL; - nand->ecc.write_page = NULL; - nand->ecc.read_oob = NULL; - nand->ecc.write_oob = NULL; - nand->ecc.hwctl = NULL; - nand->ecc.correct = NULL; - nand->ecc.calculate = NULL; - nand->ecc.strength = eccstrength; - + nand->options &= ~NAND_SUBPAGE_READ; /* Setup the ecc configurations again */ if (hardware) { if (eccstrength == 1) { - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_nand_oob; - nand->ecc.size = 512; - nand->ecc.bytes = 3; - nand->ecc.hwctl = omap_enable_hwecc; - nand->ecc.correct = omap_correct_data; - nand->ecc.calculate = omap_calculate_ecc; - omap_hwecc_init(nand); - printf("1-bit hamming HW ECC selected\n"); - } -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) - else if (eccstrength == 8) { - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_bch8_nand_oob; - nand->ecc.size = 512; -#ifdef CONFIG_AM33XX - nand->ecc.bytes = 14; - nand->ecc.read_page = omap_read_page_bch; -#else - nand->ecc.bytes = 13; -#endif - nand->ecc.hwctl = omap_enable_ecc_bch; - nand->ecc.correct = omap_correct_data_bch; - nand->ecc.calculate = omap_calculate_ecc_bch; - omap_hwecc_init_bch(nand, NAND_ECC_READ); - printf("8-bit BCH HW ECC selected\n"); + err = omap_select_ecc_scheme(nand, + OMAP_ECC_HAM1_CODE_HW, + mtd->writesize, mtd->oobsize); + } else if (eccstrength == 8) { + err = omap_select_ecc_scheme(nand, + OMAP_ECC_BCH8_CODE_HW, + mtd->writesize, mtd->oobsize); + } else { + printf("nand: error: unsupported ECC scheme\n"); + return -EINVAL; } -#endif } else { - nand->ecc.mode = NAND_ECC_SOFT; - /* Use mtd default settings */ - nand->ecc.layout = NULL; - nand->ecc.size = 0; - printf("SW ECC selected\n"); + err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW, + mtd->writesize, mtd->oobsize); } /* Update NAND handling after ECC mode switch */ - nand_scan_tail(mtd); - - nand->options &= ~NAND_OWN_BUFFERS; + if (!err) + err = nand_scan_tail(mtd); + return err; } #endif /* CONFIG_SPL_BUILD */ @@ -856,7 +979,7 @@ int board_nand_init(struct nand_chip *nand) { int32_t gpmc_config = 0; cs = 0; - + int err = 0; /* * xloader/Uboot's gpmc configuration would have configured GPMC for * nand type of memory. The following logic scans and latches on to the @@ -873,7 +996,7 @@ int board_nand_init(struct nand_chip *nand) cs++; } if (cs >= GPMC_MAX_CS) { - printf("NAND: Unable to find NAND settings in " + printf("nand: error: Unable to find NAND settings in " "GPMC Configuration - quitting\n"); return -ENODEV; } @@ -885,64 +1008,27 @@ int board_nand_init(struct nand_chip *nand) nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat; nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd; - - nand->cmd_ctrl = omap_nand_hwcontrol; - nand->options = NAND_NO_PADDING | NAND_CACHEPRG; + nand->priv = &bch_priv; + nand->cmd_ctrl = omap_nand_hwcontrol; + nand->options |= NAND_NO_PADDING | NAND_CACHEPRG; /* If we are 16 bit dev, our gpmc config tells us that */ if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) nand->options |= NAND_BUSWIDTH_16; nand->chip_delay = 100; + nand->ecc.layout = &omap_ecclayout; -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) -#ifdef CONFIG_AM33XX - /* AM33xx uses the ELM */ - /* required in case of BCH */ - elm_init(); -#else - /* - * Whereas other OMAP based SoC do not have the ELM, they use the BCH - * SW library. - */ - bch_priv.control = init_bch(13, 8, 0x201b /* hw polynominal */); - if (!bch_priv.control) { - puts("Could not init_bch()\n"); - return -ENODEV; - } -#endif - /* BCH info that will be correct for SPL or overridden otherwise. */ - nand->priv = &bch_priv; -#endif - - /* Default ECC mode */ -#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_bch8_nand_oob; - nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; - nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; - nand->ecc.strength = 8; - nand->ecc.hwctl = omap_enable_ecc_bch; - nand->ecc.correct = omap_correct_data_bch; - nand->ecc.calculate = omap_calculate_ecc_bch; -#ifdef CONFIG_AM33XX - nand->ecc.read_page = omap_read_page_bch; -#endif - omap_hwecc_init_bch(nand, NAND_ECC_READ); + /* select ECC scheme */ +#if defined(CONFIG_NAND_OMAP_ECCSCHEME) + err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME, + CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE); #else -#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC) - nand->ecc.mode = NAND_ECC_SOFT; -#else - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.layout = &hw_nand_oob; - nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; - nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; - nand->ecc.hwctl = omap_enable_hwecc; - nand->ecc.correct = omap_correct_data; - nand->ecc.calculate = omap_calculate_ecc; - nand->ecc.strength = 1; - omap_hwecc_init(nand); -#endif + /* pagesize and oobsize are not required to configure sw ecc-scheme */ + err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW, + 0, 0); #endif + if (err) + return err; #ifdef CONFIG_SPL_BUILD if (nand->options & NAND_BUSWIDTH_16)