X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=drivers%2Fmmc%2FKconfig;h=2bc9d8d22d335211135820c8e381afd98c209bc6;hb=44fb0d6c9f5147a41c710032869e5e01b3c9e310;hp=693b3ceaf007bc83dc35a5393f9c8d51f6f22ca8;hpb=5a7b11e65a54ab9f82bb08bfc402aa4ca1aa3a78;p=platform%2Fkernel%2Fu-boot.git diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index 693b3ce..2bc9d8d 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig @@ -46,6 +46,24 @@ config SPL_DM_MMC if MMC +config MMC_SPI + bool "Support for SPI-based MMC controller" + depends on DM_MMC && DM_SPI + help + This selects SPI-based MMC controllers. + If you have an MMC controller on a SPI bus, say Y here. + + If unsure, say N. + +config MMC_SPI_CRC_ON + bool "Support CRC for SPI-based MMC controller" + depends on MMC_SPI + default y + help + This enables CRC for SPI-based MMC controllers. + + If unsure, say N. + config ARM_PL180_MMCI bool "ARM AMBA Multimedia Card Interface and compatible support" depends on DM_MMC && OF_CONTROL @@ -78,6 +96,12 @@ config SUPPORT_EMMC_RPMB Enable support for reading, writing and programming the key for the Replay Protection Memory Block partition in eMMC. +config SUPPORT_EMMC_BOOT + bool "Support some additional features of the eMMC boot partitions" + help + Enable support for eMMC boot partitions. This also enables + extensions within the mmc command. + config MMC_IO_VOLTAGE bool "Support IO voltage configuration" help @@ -111,13 +135,38 @@ config SPL_MMC_UHS_SUPPORT cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus frequency can go up to 208MHz (SDR104) +config MMC_HS400_ES_SUPPORT + bool "enable HS400 Enhanced Strobe support" + help + The HS400 Enhanced Strobe mode is support by some eMMC. The bus + frequency is up to 200MHz. This mode does not tune the IO. + +config SPL_MMC_HS400_ES_SUPPORT + bool "enable HS400 Enhanced Strobe support in SPL" + help + The HS400 Enhanced Strobe mode is support by some eMMC. The bus + frequency is up to 200MHz. This mode does not tune the IO. + +config MMC_HS400_SUPPORT + bool "enable HS400 support" + select MMC_HS200_SUPPORT + help + The HS400 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + +config SPL_MMC_HS400_SUPPORT + bool "enable HS400 support in SPL" + select SPL_MMC_HS200_SUPPORT + help + The HS400 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + config MMC_HS200_SUPPORT bool "enable HS200 support" help The HS200 mode is support by some eMMC. The bus frequency is up to 200MHz. This mode requires tuning the IO. - config SPL_MMC_HS200_SUPPORT bool "enable HS200 support in SPL" help @@ -139,21 +188,6 @@ config MMC_TRACE If you need to see the MMC core message, say Y. -config SPL_MMC_TINY - bool "Tiny MMC framework in SPL" - help - Enable MMC framework tinification support. This option is useful if - if your SPL is extremely size constrained. Heed the warning, enable - this option if and only if you know exactly what you are doing, if - you are reading this help text, you most likely have no idea :-) - - The MMC framework is reduced to bare minimum to be useful. No malloc - support is needed for the MMC framework operation with this option - enabled. The framework supports exactly one MMC device and exactly - one MMC driver. The MMC driver can be adjusted to avoid any malloc - operations too, which can remove the need for malloc support in SPL - and thus further reduce footprint. - config MMC_DAVINCI bool "TI DAVINCI Multimedia Card Interface support" depends on ARCH_DAVINCI @@ -165,6 +199,7 @@ config MMC_DAVINCI config MMC_DW bool "Synopsys DesignWare Memory Card Interface" + select BOUNCE_BUFFER help This selects support for the Synopsys DesignWare Mobile Storage IP block, this provides host support for SD and MMC interfaces, in both @@ -208,6 +243,16 @@ config MMC_DW_SOCFPGA Synopsys DesignWare Memory Card Interface driver. Select this option for platforms based on Altera SOCFPGA. +config MMC_DW_SNPS + bool "Extensions for DW Memory Card Interface used in Synopsys ARC devboards" + depends on MMC_DW + depends on DM_MMC + depends on OF_CONTROL + depends on CLK + help + This selects support for Synopsys DesignWare Memory Card Interface driver + extensions used in various Synopsys ARC devboards. + config MMC_MESON_GX bool "Meson GX EMMC controller support" depends on DM_MMC && BLK && ARCH_MESON @@ -226,6 +271,7 @@ config MMC_MXC config MMC_MXS bool "Freescale MXS Multimedia Card Interface support" depends on MX23 || MX28 || MX6 || MX7 + select BOUNCE_BUFFER select APBH_DMA select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7 select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7 @@ -319,6 +365,12 @@ config MMC_BCM2835 If unsure, say N. +config JZ47XX_MMC + bool "Ingenic JZ47xx SD/MMC Host Controller support" + depends on ARCH_JZ47XX + help + This selects support for the SD Card Controller on Ingenic JZ47xx SoCs. + config MMC_SANDBOX bool "Sandbox MMC support" depends on SANDBOX @@ -354,6 +406,31 @@ config MMC_SDHCI_SDMA This enables support for the SDMA (Single Operation DMA) defined in the SD Host Controller Standard Specification Version 1.00 . +config MMC_SDHCI_ADMA + bool "Support SDHCI ADMA2" + depends on MMC_SDHCI + help + This enables support for the ADMA (Advanced DMA) defined + in the SD Host Controller Standard Specification Version 3.00 + +config SPL_MMC_SDHCI_ADMA + bool "Support SDHCI ADMA2 in SPL" + depends on MMC_SDHCI + help + This enables support for the ADMA (Advanced DMA) defined + in the SD Host Controller Standard Specification Version 3.00 in SPL. + +config MMC_SDHCI_ASPEED + bool "Aspeed SDHCI controller" + depends on ARCH_ASPEED + depends on DM_MMC + depends on MMC_SDHCI + help + Enables support for the Aspeed SDHCI 2.0 controller present on Aspeed + SoCs. This device is compatible with SD 3.0 and/or MMC 4.3 + specifications. On the AST2600, the device is also compatible with + MMC 5.1 and eMMC 3.0. + config MMC_SDHCI_ATMEL bool "Atmel SDHCI controller support" depends on ARCH_AT91 @@ -379,6 +456,17 @@ config MMC_SDHCI_BCM2835 If unsure, say N. +config MMC_SDHCI_BCMSTB + tristate "SDHCI support for the BCMSTB SD/MMC Controller" + depends on MMC_SDHCI + help + This selects the Broadcom set-top box SD/MMC controller. + + If you have a BCMSTB platform with SD or MMC devices, + say Y here. + + If unsure, say N. + config MMC_SDHCI_CADENCE bool "SDHCI support for the Cadence SD/SDIO/eMMC controller" depends on BLK && DM_MMC @@ -391,6 +479,16 @@ config MMC_SDHCI_CADENCE If unsure, say N. +config MMC_SDHCI_AM654 + bool "SDHCI Controller on TI's Am654 devices" + depends on ARCH_K3 + depends on MMC_SDHCI + depends on DM_MMC && OF_CONTROL && BLK + depends on REGMAP + help + Support for Secure Digital Host Controller Interface (SDHCI) + controllers present on TI's AM654 SOCs. + config MMC_SDHCI_KONA bool "SDHCI support on Broadcom KONA platform" depends on MMC_SDHCI @@ -496,6 +594,7 @@ config MMC_SDHCI_TANGIER config MMC_SDHCI_TEGRA bool "SDHCI platform support for the Tegra SD/MMC Controller" depends on TEGRA + select BOUNCE_BUFFER default y help This selects the Tegra SD/MMC controller. If you have a Tegra @@ -503,9 +602,20 @@ config MMC_SDHCI_TEGRA If unsure, say N. +config TEGRA124_MMC_DISABLE_EXT_LOOPBACK + bool "Disable external clock loopback" + depends on MMC_SDHCI_TEGRA && TEGRA124 + help + Disable the external clock loopback and use the internal one on SDMMC3 + as per the SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits + being set to 0xfffd according to the TRM. + + TODO(marcel.ziswiler@toradex.com): Move to device tree controlled + approach once proper kernel integration made it mainline. + config MMC_SDHCI_ZYNQ bool "Arasan SDHCI controller support" - depends on ARCH_ZYNQ || ARCH_ZYNQMP + depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL depends on DM_MMC && OF_CONTROL && BLK depends on MMC_SDHCI help @@ -524,6 +634,12 @@ config ZYNQ_SDHCI_MIN_FREQ help Set the minimum frequency of the controller. +config ZYNQ_HISPD_BROKEN + bool "High speed broken for Zynq SDHCI controller" + depends on MMC_SDHCI_ZYNQ + help + Set if high speed mode is broken. + config MMC_SUNXI bool "Allwinner sunxi SD/MMC Host Controller support" depends on ARCH_SUNXI && !UART0_PORT_F @@ -536,6 +652,10 @@ config MMC_SUNXI_HAS_NEW_MODE bool depends on MMC_SUNXI +config MMC_SUNXI_HAS_MODE_SWITCH + bool + depends on MMC_SUNXI + config GENERIC_ATMEL_MCI bool "Atmel Multimedia Card Interface support" depends on DM_MMC && BLK && ARCH_AT91 @@ -565,24 +685,46 @@ config FTSDC010_SDIO help This can enable ftsdc010 sdio function. -endif - -config TEGRA124_MMC_DISABLE_EXT_LOOPBACK - bool "Disable external clock loopback" - depends on MMC_SDHCI_TEGRA && TEGRA124 +config MMC_MTK + bool "MediaTek SD/MMC Card Interface support" + depends on ARCH_MEDIATEK + depends on BLK && DM_MMC + depends on OF_CONTROL help - Disable the external clock loopback and use the internal one on SDMMC3 - as per the SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits - being set to 0xfffd according to the TRM. + This selects the MediaTek(R) Secure digital and Multimedia card Interface. + If you have a machine with a integrated SD/MMC card reader, say Y or M here. + This is needed if support for any SD/SDIO/MMC devices is required. + If unsure, say N. - TODO(marcel.ziswiler@toradex.com): Move to device tree controlled - approach once proper kernel integration made it mainline. +endif config FSL_ESDHC bool "Freescale/NXP eSDHC controller support" + select FSL_ESDHC_USE_PERIPHERAL_CLK if MMC_HS200_SUPPORT || MMC_UHS_SUPPORT + help + This selects support for the eSDHC (Enhanced Secure Digital Host + Controller) found on numerous Freescale/NXP SoCs. + +config FSL_ESDHC_USE_PERIPHERAL_CLK + bool "enable ESDHC peripheral clock support" + depends on FSL_ESDHC + help + eSDHC supports two reference clocks (platform clock and peripheral clock). + Peripheral clock which could provide higher clock frequency is required to + be used for tuning of SD UHS mode and eMMC HS200/HS400 modes. + +config FSL_ESDHC_IMX + bool "Freescale/NXP i.MX eSDHC controller support" + help + This selects support for the i.MX eSDHC (Enhanced Secure Digital Host + Controller) found on numerous Freescale/NXP SoCs. + +config FSL_USDHC + bool "Freescale/NXP i.MX uSDHC controller support" + depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || TARGET_S32V234EVB + select FSL_ESDHC_IMX help - This selects support for the eSDHC (enhanced secure digital host - controller) found on numerous Freescale/NXP SoCs. + This enables the Ultra Secured Digital Host Controller enhancements endmenu