X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=cmd%2FKconfig;h=1ca91fcc3848e32dd36b895a269e451229ceb1d2;hb=72c3033fd1da878aec6b23eb9086a83f57d54eee;hp=2caa0b42d8910c29b35a3f9aeb51972437a1edfa;hpb=fa379223cd61052331342e525778d96270ee6ed9;p=platform%2Fkernel%2Fu-boot.git

diff --git a/cmd/Kconfig b/cmd/Kconfig
index 2caa0b4..1ca91fc 100644
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -276,6 +276,15 @@ config CMD_POWEROFF
 	help
 	  Poweroff/Shutdown the system
 
+config CMD_SPL
+	bool "spl export - Export boot information for Falcon boot"
+	depends on SPL
+	help
+	  Falcon mode allows booting directly from SPL into an Operating
+	  System such as Linux, thus skipping U-Boot proper. See
+	  doc/README.falcon for full information about how to use this
+	  command.
+
 endmenu
 
 menu "Environment commands"
@@ -779,11 +788,35 @@ config CMD_SATA
 	  Attachment, where AT refers to an IBM AT (Advanced Technology)
 	  computer released in 1984.
 
+config CMD_SAVES
+	bool "saves - Save a file over serial in S-Record format"
+	help
+	  Provides a way to save a binary file using the Motorola S-Record
+	  format over the serial line.
+
+config CMD_SDRAM
+	bool "sdram - Print SDRAM configuration information"
+	help
+	  Provides information about attached SDRAM. This assumed that the
+	  SDRAM has an EEPROM with information that can be read using the
+	  I2C bus. This is only available on some boards.
+
 config CMD_SF
 	bool "sf"
 	help
 	  SPI Flash support
 
+config CMD_SF_TEST
+	bool "sf test - Allow testing of SPI flash"
+	help
+	  Provides a way to test that SPI flash is working correctly. The
+	  test is destructive, in that an area of SPI flash must be provided
+	  for the test to use. Performance information is also provided,
+	  measuring the performance of reading, writing and erasing in
+	  Mbps (Million Bits Per Second). This value should approximately
+	  equal the SPI bus speed for a single-bit-wide SPI bus, assuming
+	  everything is working properly.
+
 config CMD_SPI
 	bool "sspi"
 	help
@@ -1275,6 +1308,24 @@ config CMD_MTDPARTS_SPREAD
 	  at least as large as the size specified in the mtdparts variable and
 	  2) each partition starts on a good block.
 
+config CMD_REISER
+	bool "reiser - Access to reiserfs filesystems"
+	help
+	  This provides two commands which operate on a resierfs filesystem,
+	  commonly used some years ago:
+
+	    reiserls - list files
+	    reiserload - load a file
+
+config CMD_SCSI
+	bool "scsi - Access to SCSI devices"
+	default y if SCSI
+	help
+	  This provides a 'scsi' command which provides access to SCSI (Small
+	  Computer System Interface) devices. The command provides a way to
+	  scan the bus, reset the bus, read and write data and get information
+	  about devices.
+
 endmenu
 
 menu "Debug commands"