X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=board%2Fsunxi%2FKconfig;h=e744d4af4e434f8e224902b6989974d4e497d39a;hb=563e53efaadd76def21612bcf9f0236d870b6e68;hp=61b4959576d4908370e2bc08826cb518de784d7b;hpb=2fbf091a547177fcf1a4b31b01ee0636c2a4aedc;p=platform%2Fkernel%2Fu-boot.git diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 61b4959..e744d4a 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -1,200 +1,207 @@ if ARCH_SUNXI +# Note only one of these may be selected at a time! But hidden choices are +# not supported by Kconfig +config SUNXI_GEN_SUN4I + bool + ---help--- + Select this for sunxi SoCs which have resets and clocks set up + as the original A10 (mach-sun4i). + +config SUNXI_GEN_SUN6I + bool + ---help--- + Select this for sunxi SoCs which have sun6i like periphery, like + separate ahb reset control registers, custom pmic bus, new style + watchdog, etc. + + choice prompt "Sunxi SoC Variant" + optional config MACH_SUN4I bool "sun4i (Allwinner A10)" select CPU_V7 + select SUNXI_GEN_SUN4I select SUPPORT_SPL config MACH_SUN5I bool "sun5i (Allwinner A13)" select CPU_V7 + select SUNXI_GEN_SUN4I select SUPPORT_SPL config MACH_SUN6I bool "sun6i (Allwinner A31)" select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SUNXI_GEN_SUN6I select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT config MACH_SUN7I bool "sun7i (Allwinner A20)" select CPU_V7 select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select SUNXI_GEN_SUN4I select SUPPORT_SPL select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT -config MACH_SUN8I +config MACH_SUN8I_A23 bool "sun8i (Allwinner A23)" select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SUNXI_GEN_SUN6I select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN8I_A33 + bool "sun8i (Allwinner A33)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN9I + bool "sun9i (Allwinner A80)" + select CPU_V7 + select SUNXI_GEN_SUN6I endchoice -if MACH_SUN6I || MACH_SUN8I +# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" +config MACH_SUN8I + bool + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 + config DRAM_CLK - int "sun6i dram clock speed" - default 312 + int "sunxi dram clock speed" + default 312 if MACH_SUN6I || MACH_SUN8I + default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I ---help--- Set the dram clock speed, valid range 240 - 480, must be a multiple of 24. +if MACH_SUN5I || MACH_SUN7I +config DRAM_MBUS_CLK + int "sunxi mbus clock speed" + default 300 + ---help--- + Set the mbus clock speed. The maximum on sun5i hardware is 300MHz. + +endif + config DRAM_ZQ - int "sun6i dram zq value" - default 123 + int "sunxi dram zq value" + default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I + default 127 if MACH_SUN7I ---help--- Set the dram zq value. +config DRAM_ODT_EN + bool "sunxi dram odt enable" + default n if !MACH_SUN8I_A23 + default y if MACH_SUN8I_A23 + ---help--- + Select this to enable dram odt (on die termination). + +if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I +config DRAM_EMR1 + int "sunxi dram emr1 value" + default 0 if MACH_SUN4I + default 4 if MACH_SUN5I || MACH_SUN7I + ---help--- + Set the dram controller emr1 value. + +config DRAM_TPR3 + hex "sunxi dram tpr3 value" + default 0 + ---help--- + Set the dram controller tpr3 parameter. This parameter configures + the delay on the command lane and also phase shifts, which are + applied for sampling incoming read data. The default value 0 + means that no phase/delay adjustments are necessary. Properly + configuring this parameter increases reliability at high DRAM + clock speeds. + +config DRAM_DQS_GATING_DELAY + hex "sunxi dram dqs_gating_delay value" + default 0 + ---help--- + Set the dram controller dqs_gating_delay parmeter. Each byte + encodes the DQS gating delay for each byte lane. The delay + granularity is 1/4 cycle. For example, the value 0x05060606 + means that the delay is 5 quarter-cycles for one lane (1.25 + cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes. + The default value 0 means autodetection. The results of hardware + autodetection are not very reliable and depend on the chip + temperature (sometimes producing different results on cold start + and warm reboot). But the accuracy of hardware autodetection + is usually good enough, unless running at really high DRAM + clocks speeds (up to 600MHz). If unsure, keep as 0. + +choice + prompt "sunxi dram timings" + default DRAM_TIMINGS_VENDOR_MAGIC + ---help--- + Select the timings of the DDR3 chips. + +config DRAM_TIMINGS_VENDOR_MAGIC + bool "Magic vendor timings from Android" + ---help--- + The same DRAM timings as in the Allwinner boot0 bootloader. + +config DRAM_TIMINGS_DDR3_1066F_1333H + bool "JEDEC DDR3-1333H with down binning to DDR3-1066F" + ---help--- + Use the timings of the standard JEDEC DDR3-1066F speed bin for + DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin + for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips + used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333 + or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm + that down binning to DDR3-1066F is supported (because DDR3-1066F + uses a bit faster timings than DDR3-1333H). + +config DRAM_TIMINGS_DDR3_800E_1066G_1333J + bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J" + ---help--- + Use the timings of the slowest possible JEDEC speed bin for the + selected DRAM_CLK. Depending on the DRAM_CLK value, it may be + DDR3-800E, DDR3-1066G or DDR3-1333J. + +endchoice + +endif + +if MACH_SUN8I_A23 +config DRAM_ODT_CORRECTION + int "sunxi dram odt correction value" + default 0 + ---help--- + Set the dram odt correction value (range -255 - 255). In allwinner + fex files, this option is found in bits 8-15 of the u32 odt_en variable + in the [dram] section. When bit 31 of the odt_en variable is set + then the correction is negative. Usually the value for this is 0. endif +config SYS_CLK_FREQ + default 912000000 if MACH_SUN7I + default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I + config SYS_CONFIG_NAME default "sun4i" if MACH_SUN4I default "sun5i" if MACH_SUN5I default "sun6i" if MACH_SUN6I default "sun7i" if MACH_SUN7I default "sun8i" if MACH_SUN8I - -choice - prompt "Board" - -config TARGET_A10_OLINUXINO_L - bool "A10_OLINUXINO_L" - depends on MACH_SUN4I - -config TARGET_A10S_OLINUXINO_M - bool "A10S_OLINUXINO_M" - depends on MACH_SUN5I - -config TARGET_A13_OLINUXINOM - bool "A13_OLINUXINOM" - depends on MACH_SUN5I - -config TARGET_A13_OLINUXINO - bool "A13_OLINUXINO" - depends on MACH_SUN5I - -config TARGET_A20_OLINUXINO_L2 - bool "A20_OLINUXINO_L2" - depends on MACH_SUN7I - -config TARGET_A20_OLINUXINO_L - bool "A20_OLINUXINO_L" - depends on MACH_SUN7I - -config TARGET_A20_OLINUXINO_M - bool "A20_OLINUXINO_M" - depends on MACH_SUN7I - -config TARGET_AUXTEK_T004 - bool "AUXTEK_T004" - depends on MACH_SUN5I - -config TARGET_BANANAPI - bool "BANANAPI" - depends on MACH_SUN7I - -config TARGET_BANANAPRO - bool "BANANAPRO" - depends on MACH_SUN7I - -config TARGET_COLOMBUS - bool "COLOMBUS" - depends on MACH_SUN6I - -config TARGET_CUBIEBOARD2 - bool "CUBIEBOARD2" - depends on MACH_SUN7I - -config TARGET_CUBIEBOARD - bool "CUBIEBOARD" - depends on MACH_SUN4I - -config TARGET_CUBIETRUCK - bool "CUBIETRUCK" - depends on MACH_SUN7I - -config TARGET_HUMMINGBIRD_A31 - bool "HUMMINGBIRD_A31" - depends on MACH_SUN6I - -config TARGET_IPPO_Q8H_V5 - bool "IPPO_Q8H_V5" - depends on MACH_SUN8I - -config TARGET_PCDUINO3 - bool "PCDUINO3" - depends on MACH_SUN7I - -config TARGET_MELE_A1000G - bool "MELE_A1000G" - depends on MACH_SUN4I - -config TARGET_MELE_A1000 - bool "MELE_A1000" - depends on MACH_SUN4I - -config TARGET_MELE_M3 - bool "MELE_M3" - depends on MACH_SUN7I - -config TARGET_MELE_M9 - bool "MELE_M9" - depends on MACH_SUN6I - -config TARGET_MINI_X_1GB - bool "MINI_X_1GB" - depends on MACH_SUN4I - -config TARGET_MINI_X - bool "MINI_X" - depends on MACH_SUN4I - -config TARGET_MSI_PRIMO73 - bool "MSI Primo73 (7\" tablet)" - depends on MACH_SUN7I - ---help--- - The MSI Primo73 is an A20 based tablet, with 1G RAM, 16G NAND, - 1024x600 TN LCD display, mono speaker, 0.3 MP front camera, 2.0 MP - rear camera, 3000 mAh battery, gt911 touchscreen, mma8452 accelerometer - and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons - (both volume buttons are also connected to the UBOOT_SEL pin). The - external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB - OTG and 3.5mm headphone jack. More details are available at - http://linux-sunxi.org/MSI_Primo73 - -config TARGET_MSI_PRIMO81 - bool "MSI Primo81 (7.85\" tablet)" - depends on MACH_SUN6I - ---help--- - The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND, - 1024x768 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP - rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer - and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons - (both volume buttons are also connected to the UBOOT_SEL pin). The - external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB - OTG and 3.5mm headphone jack. More details are available at - http://linux-sunxi.org/MSI_Primo81 - -config TARGET_BA10_TV_BOX - bool "BA10_TV_BOX" - depends on MACH_SUN4I - -config TARGET_I12_TVBOX - bool "I12_TVBOX" - depends on MACH_SUN7I - -config TARGET_QT840A - bool "QT840A" - depends on MACH_SUN7I - -config TARGET_R7DONGLE - bool "R7DONGLE" - depends on MACH_SUN5I - -endchoice + default "sun9i" if MACH_SUN9I config SYS_BOARD default "sunxi" @@ -202,14 +209,8 @@ config SYS_BOARD config SYS_SOC default "sunxi" -config SPL_FEL - bool "SPL/FEL mode support" - depends on SPL - default n - config UART0_PORT_F bool "UART0 on MicroSD breakout board" - depends on SPL_FEL default n ---help--- Repurpose the SD card slot for getting access to the UART0 serial @@ -219,9 +220,6 @@ config UART0_PORT_F at the same time, the system can be only booted in the FEL mode. Only enable this if you really know what you are doing. -config FDTFILE - string "Default fdtfile env setting for this board" - config OLD_SUNXI_KERNEL_COMPAT boolean "Enable workarounds for booting old kernels" default n @@ -255,6 +253,25 @@ config MMC3_CD_PIN ---help--- See MMC0_CD_PIN help text. +config MMC1_PINS + string "Pins for mmc1" + default "" + ---help--- + Set the pins used for mmc1, when applicable. This takes a string in the + format understood by sunxi_name_to_gpio_bank, e.g. PH for port H. + +config MMC2_PINS + string "Pins for mmc2" + default "" + ---help--- + See MMC1_PINS help text. + +config MMC3_PINS + string "Pins for mmc3" + default "" + ---help--- + See MMC1_PINS help text. + config MMC_SUNXI_SLOT_EXTRA int "mmc extra slot number" default -1 @@ -263,6 +280,32 @@ config MMC_SUNXI_SLOT_EXTRA slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable support for this. +config SPL_NAND_SUPPORT + bool "SPL/NAND mode support" + depends on SPL + default n + ---help--- + This enables support for booting from NAND internal + memory. U-Boot SPL doesn't detect where is it load from, + therefore this option is needed to properly load image from + flash. Option also disables MMC functionality on U-Boot due to + initialization errors encountered, when both controllers are + enabled. + +config USB0_VBUS_PIN + string "Vbus enable pin for usb0 (otg)" + default "" + ---help--- + Set the Vbus enable pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config USB0_VBUS_DET + string "Vbus detect pin for usb0 (otg)" + default "" + ---help--- + Set the Vbus detect pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + config USB1_VBUS_PIN string "Vbus enable pin for usb1 (ehci0)" default "PH6" if MACH_SUN4I || MACH_SUN7I @@ -279,6 +322,50 @@ config USB2_VBUS_PIN ---help--- See USB1_VBUS_PIN help text. +config I2C0_ENABLE + bool "Enable I2C/TWI controller 0" + default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + default n if MACH_SUN6I || MACH_SUN8I + ---help--- + This allows enabling I2C/TWI controller 0 by muxing its pins, enabling + its clock and setting up the bus. This is especially useful on devices + with slaves connected to the bus or with pins exposed through e.g. an + expansion port/header. + +config I2C1_ENABLE + bool "Enable I2C/TWI controller 1" + default n + ---help--- + See I2C0_ENABLE help text. + +config I2C2_ENABLE + bool "Enable I2C/TWI controller 2" + default n + ---help--- + See I2C0_ENABLE help text. + +if MACH_SUN6I || MACH_SUN7I +config I2C3_ENABLE + bool "Enable I2C/TWI controller 3" + default n + ---help--- + See I2C0_ENABLE help text. +endif + +if MACH_SUN7I +config I2C4_ENABLE + bool "Enable I2C/TWI controller 4" + default n + ---help--- + See I2C0_ENABLE help text. +endif + +config AXP_GPIO + boolean "Enable support for gpio-s on axp PMICs" + default n + ---help--- + Say Y here to enable support for the gpio pins of the axp PMIC ICs. + config VIDEO boolean "Enable graphical uboot console on HDMI, LCD or VGA" default y @@ -294,6 +381,40 @@ config VIDEO_HDMI ---help--- Say Y here to add support for outputting video over HDMI. +config VIDEO_VGA + boolean "VGA output support" + depends on VIDEO && (MACH_SUN4I || MACH_SUN7I) + default n + ---help--- + Say Y here to add support for outputting video over VGA. + +config VIDEO_VGA_VIA_LCD + boolean "VGA via LCD controller support" + depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I) + default n + ---help--- + Say Y here to add support for external DACs connected to the parallel + LCD interface driving a VGA connector, such as found on the + Olimex A13 boards. + +config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH + boolean "Force sync active high for VGA via LCD controller support" + depends on VIDEO_VGA_VIA_LCD + default n + ---help--- + Say Y here if you've a board which uses opendrain drivers for the vga + hsync and vsync signals. Opendrain drivers cannot generate steep enough + positive edges for a stable video output, so on boards with opendrain + drivers the sync signals must always be active high. + +config VIDEO_VGA_EXTERNAL_DAC_EN + string "LCD panel power enable pin" + depends on VIDEO_VGA_VIA_LCD + default "" + ---help--- + Set the enable pin for the external VGA DAC. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + config VIDEO_LCD_MODE string "LCD panel timing details" depends on VIDEO @@ -303,6 +424,13 @@ config VIDEO_LCD_MODE This is in drivers/video/videomodes.c: video_get_params() format, e.g. x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 +config VIDEO_LCD_DCLK_PHASE + int "LCD panel display clock phase" + depends on VIDEO + default 1 + ---help--- + Select LCD panel display clock phase shift, range 0-3. + config VIDEO_LCD_POWER string "LCD panel power enable pin" depends on VIDEO @@ -311,6 +439,14 @@ config VIDEO_LCD_POWER Set the power enable pin for the LCD panel. This takes a string in the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. +config VIDEO_LCD_RESET + string "LCD panel reset pin" + depends on VIDEO + default "" + ---help--- + Set the reset pin for the LCD panel. This takes a string in the format + understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + config VIDEO_LCD_BL_EN string "LCD panel backlight enable pin" depends on VIDEO @@ -328,6 +464,95 @@ config VIDEO_LCD_BL_PWM Set the backlight pwm pin for the LCD panel. This takes a string in the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. +config VIDEO_LCD_BL_PWM_ACTIVE_LOW + bool "LCD panel backlight pwm is inverted" + depends on VIDEO + default y + ---help--- + Set this if the backlight pwm output is active low. + +config VIDEO_LCD_PANEL_I2C + bool "LCD panel needs to be configured via i2c" + depends on VIDEO + default n + ---help--- + Say y here if the LCD panel needs to be configured via i2c. This + will add a bitbang i2c controller using gpios to talk to the LCD. + +config VIDEO_LCD_PANEL_I2C_SDA + string "LCD panel i2c interface SDA pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG12" + ---help--- + Set the SDA pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_PANEL_I2C_SCL + string "LCD panel i2c interface SCL pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG10" + ---help--- + Set the SCL pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + + +# Note only one of these may be selected at a time! But hidden choices are +# not supported by Kconfig +config VIDEO_LCD_IF_PARALLEL + bool + +config VIDEO_LCD_IF_LVDS + bool + + +choice + prompt "LCD panel support" + depends on VIDEO + ---help--- + Select which type of LCD panel to support. + +config VIDEO_LCD_PANEL_PARALLEL + bool "Generic parallel interface LCD panel" + select VIDEO_LCD_IF_PARALLEL + +config VIDEO_LCD_PANEL_LVDS + bool "Generic lvds interface LCD panel" + select VIDEO_LCD_IF_LVDS + +config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828 + bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip" + select VIDEO_LCD_SSD2828 + select VIDEO_LCD_IF_PARALLEL + ---help--- + 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0 + +config VIDEO_LCD_PANEL_HITACHI_TX18D42VM + bool "Hitachi tx18d42vm LCD panel" + select VIDEO_LCD_HITACHI_TX18D42VM + select VIDEO_LCD_IF_LVDS + ---help--- + 7.85" 1024x768 Hitachi tx18d42vm LCD panel support + +config VIDEO_LCD_TL059WV5C0 + bool "tl059wv5c0 LCD panel" + select VIDEO_LCD_PANEL_I2C + select VIDEO_LCD_IF_PARALLEL + ---help--- + 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and + Aigo M60/M608/M606 tablets. + +endchoice + + +config USB_MUSB_SUNXI + bool "Enable sunxi OTG / DRC USB controller in host mode" + default n + ---help--- + Say y here to enable support for the sunxi OTG / DRC USB controller + used on almost all sunxi boards. Note currently u-boot can only have + one usb host controller enabled at a time, so enabling this on boards + which also use the ehci host controller will result in build errors. + config USB_KEYBOARD boolean "Enable USB keyboard support" default y @@ -335,4 +560,25 @@ config USB_KEYBOARD Say Y here to add support for using a USB keyboard (typically used in combination with a graphical console). +config GMAC_TX_DELAY + int "GMAC Transmit Clock Delay Chain" + default 0 + ---help--- + Set the GMAC Transmit Clock Delay Chain value. + +config SYS_MALLOC_CLEAR_ON_INIT + default n + +config NETDEVICES + default y + +config DM_ETH + default y + +config DM_SERIAL + default y + +config DM_USB + default y if !USB_MUSB_SUNXI + endif