X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=board%2Ffreescale%2Fmx51evk%2Fmx51evk.c;h=afb1c30c08ae577ed90244bba0092500bdbff224;hb=d736ebea1cc335e89643656c3db33f5df55ffb16;hp=fd7342f11271bc3947e93b5078a726bbc00a4d8c;hpb=a55d23ccf6cb90acb9667a46427670add9486aec;p=platform%2Fkernel%2Fu-boot.git

diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index fd7342f..afb1c30 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -22,6 +22,7 @@
 
 #include <common.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/mx5x_pins.h>
 #include <asm/arch/iomux.h>
@@ -31,6 +32,7 @@
 #include <i2c.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
+#include <pmic.h>
 #include <fsl_pmic.h>
 #include <mc13892.h>
 
@@ -180,36 +182,39 @@ static void setup_iomux_spi(void)
 static void power_init(void)
 {
 	unsigned int val;
-	unsigned int reg;
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
+	struct pmic *p;
+
+	pmic_init();
+	p = get_pmic();
 
 	/* Write needed to Power Gate 2 register */
-	val = pmic_reg_read(REG_POWER_MISC);
+	pmic_reg_read(p, REG_POWER_MISC, &val);
 	val &= ~PWGT2SPIEN;
-	pmic_reg_write(REG_POWER_MISC, val);
+	pmic_reg_write(p, REG_POWER_MISC, val);
 
 	/* Externally powered */
-	val = pmic_reg_read(REG_CHARGE);
+	pmic_reg_read(p, REG_CHARGE, &val);
 	val |= ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | CHGAUTOB;
-	pmic_reg_write(REG_CHARGE, val);
+	pmic_reg_write(p, REG_CHARGE, val);
 
 	/* power up the system first */
-	pmic_reg_write(REG_POWER_MISC, PWUP);
+	pmic_reg_write(p, REG_POWER_MISC, PWUP);
 
 	/* Set core voltage to 1.1V */
-	val = pmic_reg_read(REG_SW_0);
+	pmic_reg_read(p, REG_SW_0, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_100V;
-	pmic_reg_write(REG_SW_0, val);
+	pmic_reg_write(p, REG_SW_0, val);
 
 	/* Setup VCC (SW2) to 1.25 */
-	val = pmic_reg_read(REG_SW_1);
+	pmic_reg_read(p, REG_SW_1, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(REG_SW_1, val);
+	pmic_reg_write(p, REG_SW_1, val);
 
 	/* Setup 1V2_DIG1 (SW3) to 1.25 */
-	val = pmic_reg_read(REG_SW_2);
+	pmic_reg_read(p, REG_SW_2, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(REG_SW_2, val);
+	pmic_reg_write(p, REG_SW_2, val);
 	udelay(50);
 
 	/* Raise the core frequency to 800MHz */
@@ -217,59 +222,49 @@ static void power_init(void)
 
 	/* Set switchers in Auto in NORMAL mode & STANDBY mode */
 	/* Setup the switcher mode for SW1 & SW2*/
-	val = pmic_reg_read(REG_SW_4);
+	pmic_reg_read(p, REG_SW_4, &val);
 	val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
 		(SWMODE_MASK << SWMODE2_SHIFT)));
 	val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
 		(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
-	pmic_reg_write(REG_SW_4, val);
+	pmic_reg_write(p, REG_SW_4, val);
 
 	/* Setup the switcher mode for SW3 & SW4 */
-	val = pmic_reg_read(REG_SW_5);
+	pmic_reg_read(p, REG_SW_5, &val);
 	val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) |
 		(SWMODE_MASK << SWMODE4_SHIFT)));
 	val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) |
 		(SWMODE_AUTO_AUTO << SWMODE4_SHIFT);
-	pmic_reg_write(REG_SW_5, val);
+	pmic_reg_write(p, REG_SW_5, val);
 
 	/* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */
-	val = pmic_reg_read(REG_SETTING_0);
+	pmic_reg_read(p, REG_SETTING_0, &val);
 	val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK);
 	val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6;
-	pmic_reg_write(REG_SETTING_0, val);
+	pmic_reg_write(p, REG_SETTING_0, val);
 
 	/* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */
-	val = pmic_reg_read(REG_SETTING_1);
+	pmic_reg_read(p, REG_SETTING_1, &val);
 	val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
 	val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775;
-	pmic_reg_write(REG_SETTING_1, val);
+	pmic_reg_write(p, REG_SETTING_1, val);
 
 	/* Configure VGEN3 and VCAM regulators to use external PNP */
 	val = VGEN3CONFIG | VCAMCONFIG;
-	pmic_reg_write(REG_MODE_1, val);
+	pmic_reg_write(p, REG_MODE_1, val);
 	udelay(200);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg &= ~0x4000;  /* Lower reset line */
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
-
-	reg = readl(GPIO2_BASE_ADDR + 0x4);
-	reg |= 0x4000;	/* configure GPIO lines as output */
-	writel(reg, GPIO2_BASE_ADDR + 0x4);
-
-	/* Reset the ethernet controller over GPIO */
-	writel(0x1, IOMUXC_BASE_ADDR + 0x0AC);
-
 	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
 	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
 		VVIDEOEN | VAUDIOEN  | VSDEN;
-	pmic_reg_write(REG_MODE_1, val);
+	pmic_reg_write(p, REG_MODE_1, val);
+
+	mxc_request_iomux(MX51_PIN_EIM_A20, IOMUX_CONFIG_ALT1);
+	gpio_direction_output(46, 0);
 
 	udelay(500);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg |= 0x4000;
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
+	gpio_set_value(46, 1);
 }
 
 #ifdef CONFIG_FSL_ESDHC
@@ -278,9 +273,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
 	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 
 	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-		*cd = readl(GPIO1_BASE_ADDR) & 0x01;
+		*cd = gpio_get_value(0);
 	else
-		*cd = readl(GPIO1_BASE_ADDR) & 0x40;
+		*cd = gpio_get_value(6);
 
 	return 0;
 }
@@ -411,14 +406,13 @@ int board_init(void)
 {
 	system_rev = get_cpu_rev();
 
-	gd->bd->bi_arch_number = MACH_TYPE_MX51_BABBAGE;
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 
 	return 0;
 }
 
-#ifdef BOARD_LATE_INIT
+#ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
 #ifdef CONFIG_MXC_SPI