X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=board%2Fesd%2Fpci405%2Fpci405.c;h=04bc569ead1cc03a9088a2a3b0fbb19833b74ab4;hb=297a65873d2cb2bd296253af51f59cc1391afbff;hp=8973f97095c507400eb8c3fc56d3b2689d39166b;hpb=8206bfae3ab7f99965136384360ba2de0c6f4c3b;p=platform%2Fkernel%2Fu-boot.git

diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c
index 8973f97..04bc569 100644
--- a/board/esd/pci405/pci405.c
+++ b/board/esd/pci405/pci405.c
@@ -67,7 +67,7 @@ const unsigned char fpgadata[] =
 
 int board_revision(void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	unsigned long value;
 
 	/*
@@ -77,8 +77,8 @@ int board_revision(void)
 	/*
 	 * Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
-	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
 	out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00100200);
 	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00100200);
 	udelay(1000);                   /* wait some time before reading input */
@@ -87,7 +87,7 @@ int board_revision(void)
 	/*
 	 * Restore GPIO settings
 	 */
-	mtdcr(cntrl0, cntrl0Reg);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 	switch (value) {
 	case 0x00100200:
@@ -133,7 +133,7 @@ unsigned long fpga_init_state(void)
 
 int board_early_init_f (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/*
 	 * First pull fpga-prg pin low, to disable fpga logic (on version 1.2 board)
@@ -166,18 +166,18 @@ int board_early_init_f (void)
 	/*
 	 * Setup GPIO pins (IRQ4/GPIO21 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00008000);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00008000);
 
 	/*
 	 * Setup GPIO pins (CS6+CS7 as GPIO)
 	 */
-	mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
 
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }
@@ -282,11 +282,11 @@ int misc_init_r (void)
 #define PCI0_BRDGOPT1 0x4a
 	pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
 
-#define plb0_acr      0x87
+#define PLB0_ACR      0x87
 	/*
 	 * Enable fairness and high bus utilization
 	 */
-	mtdcr(plb0_acr, 0x98000000);
+	mtdcr(PLB0_ACR, 0x98000000);
 
 	free(dst);
 	return (0);
@@ -313,14 +313,14 @@ int checkboard (void)
 	printf(" (Rev 1.%ld", gd->board_type);
 
 	if (gd->board_type >= 2) {
-		unsigned long cntrl0Reg;
+		unsigned long CPC0_CR0Reg;
 		unsigned long value;
 
 		/*
 		 * Setup GPIO pins (Trace/GPIO1 to GPIO)
 		 */
-		cntrl0Reg = mfdcr(cntrl0);
-		mtdcr(cntrl0, cntrl0Reg & ~0x08000000);
+		CPC0_CR0Reg = mfdcr(CPC0_CR0);
+		mtdcr(CPC0_CR0, CPC0_CR0Reg & ~0x08000000);
 		out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x40000000);
 		out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x40000000);
 		udelay(1000);                   /* wait some time before reading input */
@@ -381,5 +381,5 @@ U_BOOT_CMD(
 	"wpeeprom 1\n"
 	"    - enable I2C EEPROM write protection\n"
 	"wpeeprom 0\n"
-	"    - disable I2C EEPROM write protection\n"
-	);
+	"    - disable I2C EEPROM write protection"
+);