X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=983d55ecea2c6a297bbccc38164b1e098d293a96;hb=c8b281524bf98ee5a52db7da71bccdea002df3f5;hp=37805649c2ae97c178c5e9c57b46f9e59badb316;hpb=eecf9e2e78c3af4304740804b3649f3d4b8a922a;p=platform%2Fkernel%2Fu-boot.git

diff --git a/README b/README
index 3780564..983d55e 100644
--- a/README
+++ b/README
@@ -413,11 +413,22 @@ The following options need to be configured:
 		See Freescale App Note 4493 for more information about
 		this erratum.
 
+		CONFIG_A003399_NOR_WORKAROUND
+		Enables a workaround for IFC erratum A003399. It is only
+		requred during NOR boot.
+
 		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
 
 		This is the value to write into CCSR offset 0x18600
 		according to the A004510 workaround.
 
+		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
+		This value denotes start offset of M2 memory
+		which is directly connected to the DSP core.
+
+		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
+		This value denotes start offset of DSP CCSR space.
+
 - Generic CPU options:
 		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
@@ -1261,6 +1272,9 @@ The following options need to be configured:
 		CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
 		txfilltuning field in the EHCI controller on reset.
 
+		CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
+		interval for usb hub power-on delay.(minimum 100msec)
+
 - USB Device:
 		Define the below if you wish to use the USB console.
 		Once firmware is rebuilt from a serial console issue the
@@ -2932,12 +2946,30 @@ FIT uImage format:
 		Address, size and partition on the MMC to load U-Boot from
 		when the MMC is being used in raw mode.
 
+		CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
+		Sector to load kernel uImage from when MMC is being
+		used in raw mode (for Falcon mode)
+
+		CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
+		CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
+		Sector and number of sectors to load kernel argument
+		parameters from when MMC is being used in raw mode
+		(for falcon mode)
+
 		CONFIG_SPL_FAT_SUPPORT
 		Support for fs/fat/libfat.o in SPL binary
 
 		CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
 		Filename to read to load U-Boot when reading from FAT
 
+		CONFIG_SPL_FAT_LOAD_KERNEL_NAME
+		Filename to read to load kernel uImage when reading
+		from FAT (for Falcon mode)
+
+		CONFIG_SPL_FAT_LOAD_ARGS_NAME
+		Filename to read to load kernel argument parameters
+		when reading from FAT (for Falcon mode)
+
 		CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
 		Set this for NAND SPL on PPC mpc83xx targets, so that
 		start.S waits for the rest of the SPL to load before
@@ -3627,6 +3659,57 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface.
 	  You will probably want to define these to avoid a really noisy system
 	  when storing the env in UBI.
 
+- CONFIG_ENV_IS_IN_MMC:
+
+	Define this if you have an MMC device which you want to use for the
+	environment.
+
+	- CONFIG_SYS_MMC_ENV_DEV:
+
+	  Specifies which MMC device the environment is stored in.
+
+	- CONFIG_SYS_MMC_ENV_PART (optional):
+
+	  Specifies which MMC partition the environment is stored in. If not
+	  set, defaults to partition 0, the user area. Common values might be
+	  1 (first MMC boot partition), 2 (second MMC boot partition).
+
+	- CONFIG_ENV_OFFSET:
+	- CONFIG_ENV_SIZE:
+
+	  These two #defines specify the offset and size of the environment
+	  area within the specified MMC device.
+
+	  If offset is positive (the usual case), it is treated as relative to
+	  the start of the MMC partition. If offset is negative, it is treated
+	  as relative to the end of the MMC partition. This can be useful if
+	  your board may be fitted with different MMC devices, which have
+	  different sizes for the MMC partitions, and you always want the
+	  environment placed at the very end of the partition, to leave the
+	  maximum possible space before it, to store other data.
+
+	  These two values are in units of bytes, but must be aligned to an
+	  MMC sector boundary.
+
+	- CONFIG_ENV_OFFSET_REDUND (optional):
+
+	  Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
+	  hold a redundant copy of the environment data. This provides a
+	  valid backup copy in case the other copy is corrupted, e.g. due
+	  to a power failure during a "saveenv" operation.
+
+	  This value may also be positive or negative; this is handled in the
+	  same way as CONFIG_ENV_OFFSET.
+
+	  This value is also in units of bytes, but must also be aligned to
+	  an MMC sector boundary.
+
+	- CONFIG_ENV_SIZE_REDUND (optional):
+
+	  This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
+	  set. If this value is set, it must be set to the same value as
+	  CONFIG_ENV_SIZE.
+
 - CONFIG_SYS_SPI_INIT_OFFSET
 
 	Defines offset to the initial SPI buffer area in DPRAM. The
@@ -3880,6 +3963,9 @@ Low Level (hardware related) configuration options:
 		a second time.	Useful for platforms that are pre-booted
 		by coreboot or similar.
 
+- CONFIG_PCI_INDIRECT_BRIDGE:
+		Enable support for indirect PCI bridges.
+
 - CONFIG_SYS_SRIO:
 		Chip has SRIO or not
 
@@ -3889,6 +3975,9 @@ Low Level (hardware related) configuration options:
 - CONFIG_SRIO2:
 		Board has SRIO 2 port available
 
+- CONFIG_SRIO_PCIE_BOOT_MASTER
+		Board can support master function for Boot from SRIO and PCIE
+
 - CONFIG_SYS_SRIOn_MEM_VIRT:
 		Virtual Address of SRIO port 'n' memory region