X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=864bf8bc2224977b08dd73ec234113d3e8c1743b;hb=4125bbcef6a998ce8580a1f5c53c8c93a56a125b;hp=3174b18d9a894737bccd47c0aaa1943ed4c974bb;hpb=b504ff9f6bbdd4d3700595f64f3c30c5c9f70d35;p=platform%2Fkernel%2Fu-boot.git diff --git a/README b/README index 3174b18..864bf8b 100644 --- a/README +++ b/README @@ -137,7 +137,6 @@ Directory Hierarchy: /arc Files generic to ARC architecture /arm Files generic to ARM architecture /avr32 Files generic to AVR32 architecture - /blackfin Files generic to Analog Devices Blackfin architecture /m68k Files generic to m68k architecture /microblaze Files generic to microblaze architecture /mips Files generic to MIPS architecture @@ -147,7 +146,6 @@ Directory Hierarchy: /powerpc Files generic to PowerPC architecture /sandbox Files generic to HW-independent "sandbox" /sh Files generic to SH architecture - /sparc Files generic to SPARC architecture /x86 Files generic to x86 architecture /api Machine/arch independent API for external apps /board Board dependent files @@ -592,14 +590,6 @@ The following options need to be configured: Select high exception vectors of the ARM core, e.g., do not clear the V bit of the c1 register of CP15. - CONFIG_SYS_THUMB_BUILD - - Use this flag to build U-Boot using the Thumb instruction - set for ARM architectures. Thumb instruction set provides - better code density. For ARM architectures that support - Thumb2 this flag will result in Thumb2 code generated by - GCC. - COUNTER_FREQUENCY Generic timer clock source frequency. @@ -833,16 +823,11 @@ The following options need to be configured: CONFIG_CMD_AES AES 128 CBC encrypt/decrypt CONFIG_CMD_ASKENV * ask for env variable CONFIG_CMD_BDI bdinfo - CONFIG_CMD_BEDBUG * Include BedBug Debugger - CONFIG_CMD_BMP * BMP support - CONFIG_CMD_BSP * Board specific commands CONFIG_CMD_BOOTD bootd CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support CONFIG_CMD_CACHE * icache, dcache - CONFIG_CMD_CLK * clock command support CONFIG_CMD_CONSOLE coninfo CONFIG_CMD_CRC32 * crc32 - CONFIG_CMD_DATE * support for RTC, date/time... CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands @@ -983,7 +968,7 @@ The following options need to be configured: tree is available in the global data as gd->fdt_blob. U-Boot needs to get its device tree from somewhere. This can - be done using one of the two options below: + be done using one of the three options below: CONFIG_OF_EMBED If this variable is defined, U-Boot will embed a device tree @@ -1004,6 +989,12 @@ The following options need to be configured: still use the individual files if you need something more exotic. + CONFIG_OF_BOARD + If this variable is defined, U-Boot will use the device tree + provided by the board at runtime instead of embedding one with + the image. Only boards defining board_fdt_blob_setup() support + this option (see include/fdtdec.h file). + - Watchdog: CONFIG_WATCHDOG If this variable is defined, it enables watchdog @@ -1559,13 +1550,6 @@ The following options need to be configured: This will also enable the command "fatwrite" enabling the user to write files to FAT. -- CBFS (Coreboot Filesystem) support: - CONFIG_CMD_CBFS - - Define this to enable support for reading from a Coreboot - filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls - and cbfsload. - - FAT(File Allocation Table) filesystem cluster size: CONFIG_FS_FAT_MAX_CLUSTSIZE @@ -1591,7 +1575,6 @@ The following options need to be configured: CONFIG_SYS_DIU_ADDR CONFIG_VIDEO - CONFIG_CMD_BMP CONFIG_CFB_CONSOLE CONFIG_VIDEO_SW_CURSOR CONFIG_VGA_AS_SINGLE_DEVICE @@ -1652,9 +1635,6 @@ The following options need to be configured: 320x240. Black & white. - Normally display is black on white background; define - CONFIG_SYS_WHITE_ON_BLACK to get it inverted. - CONFIG_LCD_ALIGNMENT Normally the LCD is page-aligned (typically 4KB). If this is @@ -2224,52 +2204,7 @@ The following options need to be configured: If you do not have i2c muxes on your board, omit this define. -- Legacy I2C Support: CONFIG_HARD_I2C - - NOTE: It is intended to move drivers to CONFIG_SYS_I2C which - provides the following compelling advantages: - - - more than one i2c adapter is usable - - approved multibus support - - better i2c mux support - - ** Please consider updating your I2C driver now. ** - - These enable legacy I2C serial bus commands. Defining - CONFIG_HARD_I2C will include the appropriate I2C driver - for the selected CPU. - - This will allow you to use i2c commands at the u-boot - command line (as long as you set CONFIG_CMD_I2C in - CONFIG_COMMANDS) and communicate with i2c based realtime - clock chips. See common/cmd_i2c.c for a description of the - command line interface. - - CONFIG_HARD_I2C selects a hardware I2C controller. - - There are several other quantities that must also be - defined when you define CONFIG_HARD_I2C. - - In both cases you will need to define CONFIG_SYS_I2C_SPEED - to be the frequency (in Hz) at which you wish your i2c bus - to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie - the CPU's i2c node address). - - Now, the u-boot i2c code for the mpc8xx - (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node - and so its address should therefore be cleared to 0 (See, - eg, MPC823e User's Manual p.16-473). So, set - CONFIG_SYS_I2C_SLAVE to 0. - - CONFIG_SYS_I2C_INIT_MPC5XXX - - When a board is reset during an i2c bus transfer - chips might think that the current transfer is still - in progress. Reset the slave devices by sending start - commands until the slave device responds. - - That's all that's required for CONFIG_HARD_I2C. - +- Legacy I2C Support: If you use the software i2c interface (CONFIG_SYS_I2C_SOFT) then the following macros need to be defined (examples are from include/configs/lwmon.h): @@ -2358,23 +2293,6 @@ The following options need to be configured: custom i2c_init_board() routine in boards/xxx/board.c is run early in the boot sequence. - CONFIG_SYS_I2C_BOARD_LATE_INIT - - An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is - defined a custom i2c_board_late_init() routine in - boards/xxx/board.c is run AFTER the operations in i2c_init() - is completed. This callpoint can be used to unreset i2c bus - using CPU i2c controller register accesses for CPUs whose i2c - controller provide such a method. It is called at the end of - i2c_init() to allow i2c_init operations to setup the i2c bus - controller on the CPU (e.g. setting bus speed & slave address). - - CONFIG_I2CFAST (PPC405GP|PPC405EP only) - - This option enables configuration of bi_iic_fast[] flags - in u-boot bd_info structure based on u-boot environment - variable "i2cfast". (see also i2cfast) - CONFIG_I2C_MULTI_BUS This option allows the use of multiple I2C buses, each of which @@ -2859,16 +2777,6 @@ The following options need to be configured: This enables 'hdmidet' command which returns true if an HDMI monitor is detected. This command is i.MX 6 specific. - CONFIG_CMD_BMODE - This enables the 'bmode' (bootmode) command for forcing - a boot from specific media. - - This is useful for forcing the ROM's usb downloader to - activate upon a watchdog reset which is nice when iterating - on U-Boot. Using the reset button or running bmode normal - will set it back to normal. This command currently - supports i.MX53 and i.MX6. - - bootcount support: CONFIG_BOOTCOUNT_LIMIT @@ -2877,8 +2785,6 @@ The following options need to be configured: CONFIG_AT91SAM9XE enable special bootcounter support on at91sam9xe based boards. - CONFIG_BLACKFIN - enable special bootcounter support on blackfin based boards. CONFIG_SOC_DA8XX enable special bootcounter support on da850 based boards. CONFIG_BOOTCOUNT_RAM @@ -3255,10 +3161,6 @@ FIT uImage format: consider that a completely unreadable NAND block is bad, and thus should be skipped silently. - CONFIG_SPL_ABORT_ON_RAW_IMAGE - When defined, SPL will proceed to another boot method - if the image it has loaded does not have a signature. - CONFIG_SPL_RELOC_STACK Adress of the start of the stack SPL will use after relocation. If unspecified, this is equal to @@ -3744,11 +3646,6 @@ Configuration Settings: If defined, don't allow the -f switch to env set override variable access flags. -- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) - This is set by OMAP boards for the max time that reset should - be asserted. See doc/README.omap-reset-time for details on how - the value can be calculated on a given board. - - CONFIG_USE_STDINT If stdint.h is available with your toolchain you can define this option to enable it. You can provide option 'USE_STDINT=1' when @@ -4548,11 +4445,6 @@ Low Level (hardware related) configuration options: If defined, the x86 reset vector code is included. This is not needed when U-Boot is running from Coreboot. -- CONFIG_SYS_MPUCLK - Defines the MPU clock speed (in MHz). - - NOTE : currently only supported on AM335x platforms. - - CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC: Enables the RTC32K OSC on AM33xx based plattforms @@ -5923,11 +5815,6 @@ For PowerPC, the following registers have specific use: average for all boards 752 bytes for the whole U-Boot image, 624 text + 127 data). -On Blackfin, the normal C ABI (except for P3) is followed as documented here: - http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface - - ==> U-Boot will use P3 to hold a pointer to the global data - On ARM, the following registers are used: R0: function argument word/integer result