X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=6b6f7227336a1fff884e755ed59cdebdec371881;hb=be0789a8ee024e685f070dbd8c58736ea3891654;hp=ff0df3797d21e63343c4caadf5093423c710368d;hpb=9ff4ce8abc627b8696c9bd6fd726dd1dbf4b9a5c;p=platform%2Fkernel%2Fu-boot.git

diff --git a/README b/README
index ff0df37..6b6f722 100644
--- a/README
+++ b/README
@@ -166,27 +166,6 @@ Directory Hierarchy:
 Software Configuration:
 =======================
 
-Configuration is usually done using C preprocessor defines; the
-rationale behind that is to avoid dead code whenever possible.
-
-There are two classes of configuration variables:
-
-* Configuration _OPTIONS_:
-  These are selectable by the user and have names beginning with
-  "CONFIG_".
-
-* Configuration _SETTINGS_:
-  These depend on the hardware etc. and should not be meddled with if
-  you don't know what you're doing; they have names beginning with
-  "CONFIG_SYS_".
-
-Previously, all configuration was done by hand, which involved creating
-symbolic links and editing configuration files manually. More recently,
-U-Boot has added the Kbuild infrastructure used by the Linux kernel,
-allowing you to use the "make menuconfig" command to configure your
-build.
-
-
 Selection of Processor Architecture and Board Type:
 ---------------------------------------------------
 
@@ -417,12 +396,6 @@ The following options need to be configured:
 		Board config to use DDR3L. It can be enabled for SoCs with
 		DDR3L controllers.
 
-		CONFIG_SYS_FSL_IFC_BE
-		Defines the IFC controller register space as Big Endian
-
-		CONFIG_SYS_FSL_IFC_LE
-		Defines the IFC controller register space as Little Endian
-
 		CONFIG_SYS_FSL_IFC_CLK_DIV
 		Defines divider of platform clock(clock input to IFC controller).
 
@@ -440,11 +413,6 @@ The following options need to be configured:
 		same as CONFIG_SYS_DDR_SDRAM_BASE for  all Power SoCs. But
 		it could be different for ARM SoCs.
 
-		CONFIG_SYS_FSL_DDR_INTLV_256B
-		DDR controller interleaving on 256-byte. This is a special
-		interleaving mode, handled by Dickens for Freescale layerscape
-		SoCs with ARM core.
-
 		CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
 		Number of controllers used as main memory.
 
@@ -1330,10 +1298,6 @@ The following options need to be configured:
 		Enables support for FPGA family.
 		(SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
 
-		CONFIG_SYS_FPGA_PROG_FEEDBACK
-
-		Enable printing of hash marks during FPGA configuration.
-
 		CONFIG_SYS_FPGA_CHECK_BUSY
 
 		Enable checks on FPGA configuration interface busy
@@ -1346,9 +1310,6 @@ The following options need to be configured:
 		If defined, a function that provides delays in the FPGA
 		configuration driver.
 
-		CONFIG_SYS_FPGA_CHECK_CTRLC
-		Allow Control-C to interrupt FPGA configuration
-
 		CONFIG_SYS_FPGA_CHECK_ERROR
 
 		Check for configuration errors during FPGA bitfile
@@ -1756,38 +1717,10 @@ Configuration Settings:
 		Enables allocating and saving a kernel copy of the bd_info in
 		space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
 
-- CONFIG_SYS_MAX_FLASH_SECT:
-		Max number of sectors on a Flash chip
-
-- CONFIG_SYS_FLASH_ERASE_TOUT:
-		Timeout for Flash erase operations (in ms)
-
-- CONFIG_SYS_FLASH_WRITE_TOUT:
-		Timeout for Flash write operations (in ms)
-
-- CONFIG_SYS_FLASH_LOCK_TOUT
-		Timeout for Flash set sector lock bit operation (in ms)
-
-- CONFIG_SYS_FLASH_UNLOCK_TOUT
-		Timeout for Flash clear lock bits operation (in ms)
-
 - CONFIG_SYS_FLASH_PROTECTION
 		If defined, hardware flash sectors protection is used
 		instead of U-Boot software protection.
 
-- CONFIG_SYS_DIRECT_FLASH_TFTP:
-
-		Enable TFTP transfers directly to flash memory;
-		without this option such a download has to be
-		performed in two steps: (1) download to RAM, and (2)
-		copy from RAM to flash.
-
-		The two-step approach is usually more reliable, since
-		you can check if the download worked before you erase
-		the flash, but in some situations (when system RAM is
-		too limited to allow for a temporary copy of the
-		downloaded image) this option may be very useful.
-
 - CONFIG_SYS_FLASH_CFI:
 		Define if the flash driver uses extra elements in the
 		common flash structure for storing flash geometry.
@@ -1808,12 +1741,6 @@ Configuration Settings:
 		s29ws-n MirrorBit flash has non-standard addresses for buffered
 		write commands.
 
-- CONFIG_SYS_FLASH_QUIET_TEST
-		If this option is defined, the common CFI flash doesn't
-		print it's warning upon not recognized FLASH banks. This
-		is useful, if some of the configured banks are only
-		optionally available.
-
 - CONFIG_FLASH_SHOW_PROGRESS
 		If defined (must be an integer), print out countdown
 		digits and dots.  Recommended value: 45 (9..1) for 80