X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=4367ac3798cedf9c3a898f16d7edbe41fc5a40bb;hb=f0e236c8d6646f6ef0ebf8f043962a07dda3b3a3;hp=841412bacc676e82ee42185f47568f2330ff2f83;hpb=3b32cf096bd6b1d8871ecaddb4250756242fb5f9;p=platform%2Fkernel%2Fu-boot.git

diff --git a/README b/README
index 841412b..4367ac3 100644
--- a/README
+++ b/README
@@ -889,15 +889,8 @@ The following options need to be configured:
 		Allow generic access to the SPI bus on the Intel 8257x, for
 		example with the "sspi" command.
 
-		CONFIG_EEPRO100
-		Support for Intel 82557/82559/82559ER chips.
-		Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
-		write routine for first time initialisation.
-
 		CONFIG_TULIP
 		Support for Digital 2114x chips.
-		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
-		modem chip initialisation (KS8761/QS6611).
 
 		CONFIG_NATSEMI
 		Support for National dp83815 chips.
@@ -1332,21 +1325,6 @@ The following options need to be configured:
 		can be displayed via the splashscreen support or the
 		bmp command.
 
-- Compression support:
-		CONFIG_GZIP
-
-		Enabled by default to support gzip compressed images.
-
-		CONFIG_BZIP2
-
-		If this option is set, support for bzip2 compressed
-		images is included. If not, only uncompressed and gzip
-		compressed images are supported.
-
-		NOTE: the bzip2 algorithm requires a lot of RAM, so
-		the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
-		be at least 4MB.
-
 - MII/PHY support:
 		CONFIG_PHY_CLOCK_FREQ (ppc4xx)
 
@@ -1569,14 +1547,6 @@ The following options need to be configured:
 
 		This enable the NEW i2c subsystem, and will allow you to use
 		i2c commands at the u-boot command line (as long as you set
-		CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
-		based realtime clock chips or other i2c devices. See
-		common/cmd_i2c.c for a description of the command line
-		interface.
-
-		ported i2c driver to the new framework:
-		- drivers/i2c/soft_i2c.c:
-		  - activate first bus with CONFIG_SYS_I2C_SOFT define
 		    CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
 		    for defining speed and slave address
 		  - activate second bus with I2C_SOFT_DECLARATIONS2 define
@@ -1632,16 +1602,6 @@ The following options need to be configured:
 		  - activate this driver with CONFIG_SYS_I2C_RCAR
 		  - This driver adds 4 i2c buses
 
-		  - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
-		  - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
-		  - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
-		  - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
-		  - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
-		  - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
-		  - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
-		  - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
-		  - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
-
 		- drivers/i2c/sh_i2c.c:
 		  - activate this driver with CONFIG_SYS_I2C_SH
 		  - This driver adds from 2 to 5 i2c buses
@@ -2485,14 +2445,6 @@ Configuration Settings:
 - CONFIG_SYS_BAUDRATE_TABLE:
 		List of legal baudrate settings for this board.
 
-- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
-		Begin and End addresses of the area used by the
-		simple memory test.
-
-- CONFIG_SYS_MEMTEST_SCRATCH:
-		Scratch address used by the alternate memory test
-		You only need to set this if address zero isn't writeable
-
 - CONFIG_SYS_MEM_RESERVE_SECURE
 		Only implemented for ARMv8 for now.
 		If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
@@ -2749,10 +2701,6 @@ Configuration Settings:
 	regular expression. This allows multiple variables to define the same
 	flags without explicitly listing them for each variable.
 
-- CONFIG_ENV_ACCESS_IGNORE_FORCE
-	If defined, don't allow the -f switch to env set override variable
-	access flags.
-
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations: