X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=3b406c2820049ad9f2f64ca9e844b6aacd57b8be;hb=437a7293a7168b6a2d356fe5d1955091afa2074f;hp=f5a719db9d3a43e0bf7e45a20e8362fc207cd770;hpb=4516ff816084605990115d127df97950c23e389c;p=platform%2Fkernel%2Fu-boot.git diff --git a/README b/README index f5a719d..3b406c2 100644 --- a/README +++ b/README @@ -690,6 +690,14 @@ The following options need to be configured: exists, unlike the similar options in the Linux kernel. Do not set these options unless they apply! + COUNTER_FREQUENCY + Generic timer clock source frequency. + + COUNTER_FREQUENCY_REAL + Generic timer clock source frequency if the real clock is + different from COUNTER_FREQUENCY, and can only be determined + at run time. + NOTE: The following can be machine specific errata. These do have ability to provide rudimentary version and machine specific checks, but expect no product checks. @@ -940,6 +948,9 @@ The following options need to be configured: bytes are output before the console is initialised, the earlier bytes are discarded. + Note that when printing the buffer a copy is made on the + stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack. + 'Sane' compilers will generate smaller code if CONFIG_PRE_CON_BUF_SZ is a power of 2 @@ -966,8 +977,6 @@ The following options need to be configured: CONFIG_AUTOBOOT_PROMPT CONFIG_AUTOBOOT_DELAY_STR CONFIG_AUTOBOOT_STOP_STR - CONFIG_AUTOBOOT_DELAY_STR2 - CONFIG_AUTOBOOT_STOP_STR2 CONFIG_ZERO_BOOTDELAY_CHECK CONFIG_RESET_TO_RETRY @@ -1865,12 +1874,6 @@ CBFS (Coreboot Filesystem) support boot. See the documentation file README.video for a description of this variable. - CONFIG_VIDEO_VGA - - Enable the VGA video / BIOS for x86. The alternative if you - are using coreboot is to use the coreboot frame buffer - driver. - - Keyboard Support: CONFIG_KEYBOARD @@ -2105,18 +2108,6 @@ CBFS (Coreboot Filesystem) support Some PHY like Intel LXT971A need extra delay after command issued before MII status register can be read -- Ethernet address: - CONFIG_ETHADDR - CONFIG_ETH1ADDR - CONFIG_ETH2ADDR - CONFIG_ETH3ADDR - CONFIG_ETH4ADDR - CONFIG_ETH5ADDR - - Define a default value for Ethernet address to use - for the respective Ethernet interface, in case this - is not determined automatically. - - IP address: CONFIG_IPADDR @@ -2871,8 +2862,8 @@ CBFS (Coreboot Filesystem) support completely disabled. Anybody can change or delete these parameters. - Alternatively, if you #define _both_ CONFIG_ETHADDR - _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default + Alternatively, if you define _both_ an ethaddr in the + default env _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default Ethernet address is installed in the environment, which can be changed exactly ONCE by the user. [The serial# is unaffected by this, i. e. it remains @@ -3088,17 +3079,6 @@ CBFS (Coreboot Filesystem) support memories can be connected with a given cs line. Currently Xilinx Zynq qspi supports these type of connections. - CONFIG_SYS_SPI_ST_ENABLE_WP_PIN - enable the W#/Vpp signal to disable writing to the status - register on ST MICRON flashes like the N25Q128. - The status register write enable/disable bit, combined with - the W#/VPP signal provides hardware data protection for the - device as follows: When the enable/disable bit is set to 1, - and the W#/VPP signal is driven LOW, the status register - nonvolatile bits become read-only and the WRITE STATUS REGISTER - operation will not execute. The only way to exit this - hardware-protected mode is to drive W#/VPP HIGH. - - SystemACE Support: CONFIG_SYSTEMACE @@ -4160,6 +4140,10 @@ Configuration Settings: list, simply add an entry for the same variable name to the ".flags" variable. + If CONFIG_REGEX is defined, the variable_name above is evaluated as a + regular expression. This allows multiple variables to define the same + flags without explicitly listing them for each variable. + - CONFIG_ENV_ACCESS_IGNORE_FORCE If defined, don't allow the -f switch to env set override variable access flags. @@ -5482,7 +5466,7 @@ loaded to, and "Flash Location" gives the image's address in NOR flash or offset in NAND flash. *Note* - these variables don't have to be defined for all boards, some -boards currenlty use other variables for these purposes, and some +boards currently use other variables for these purposes, and some boards use these variables for other purposes. Image File Name RAM Address Flash Location @@ -5558,6 +5542,10 @@ override any association in the static list. You can define CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the ".callbacks" environment variable in the default or embedded environment. +If CONFIG_REGEX is defined, the variable_name above is evaluated as a +regular expression. This allows multiple variables to be connected to +the same callback without explicitly listing them all out. + Command Line Parsing: ===================== @@ -5632,7 +5620,8 @@ o If both the SROM and the environment contain a MAC address, and the warning is printed. o If neither SROM nor the environment contain a MAC address, an error - is raised. + is raised. If CONFIG_NET_RANDOM_ETHADDR is defined, then in this case + a random, locally-assigned MAC is used. If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses will be programmed into hardware as part of the initialization process. This