X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=README;h=17d56b80349a7a97e847e30ab197e768e502b268;hb=44c214dc2738da979d277d8d45fe50997b62b5f8;hp=a91af2a1894ed9ed355e62c10996c8296ccceb49;hpb=282ce6454c45409805e2c470bbec170d21a4bd35;p=platform%2Fkernel%2Fu-boot.git

diff --git a/README b/README
index a91af2a..17d56b8 100644
--- a/README
+++ b/README
@@ -528,25 +528,6 @@ The following options need to be configured:
 		pointer. This is needed for the temporary stack before
 		relocation.
 
-		CONFIG_SYS_MIPS_CACHE_MODE
-
-		Cache operation mode for the MIPS CPU.
-		See also arch/mips/include/asm/mipsregs.h.
-		Possible values are:
-			CONF_CM_CACHABLE_NO_WA
-			CONF_CM_CACHABLE_WA
-			CONF_CM_UNCACHED
-			CONF_CM_CACHABLE_NONCOHERENT
-			CONF_CM_CACHABLE_CE
-			CONF_CM_CACHABLE_COW
-			CONF_CM_CACHABLE_CUW
-			CONF_CM_CACHABLE_ACCELERATED
-
-		CONFIG_SYS_XWAY_EBU_BOOTCFG
-
-		Special option for Lantiq XWAY SoCs for booting from NOR flash.
-		See also arch/mips/cpu/mips32/start.S.
-
 		CONFIG_XWAY_SWAP_BYTES
 
 		Enable compilation of tools/xway-swap-bytes needed for Lantiq
@@ -977,9 +958,6 @@ The following options need to be configured:
 			Define this to use i/o functions instead of macros
 			(some hardware wont work with macros)
 
-		CONFIG_DRIVER_TI_EMAC
-		Support for davinci emac
-
 			CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
 			Define this if you have more then 3 PHYs.
 
@@ -1954,14 +1932,6 @@ The following options need to be configured:
 		SPI configuration items (port pins to use, etc). For
 		an example, see include/configs/sacsng.h.
 
-		CONFIG_HARD_SPI
-
-		Enables a hardware SPI driver for general-purpose reads
-		and writes.  As with CONFIG_SOFT_SPI, the board configuration
-		must define a list of chip-select function pointers.
-		Currently supported on some MPC8xxx processors.	 For an
-		example, see include/configs/mpc8349emds.h.
-
 		CONFIG_SYS_SPI_MXC_WAIT
 		Timeout for waiting until spi transfer completed.
 		default: (CONFIG_SYS_HZ/100)     /* 10 ms */
@@ -3018,11 +2988,6 @@ Configuration Settings:
 	If defined, don't allow the -f switch to env set override variable
 	access flags.
 
-- CONFIG_USE_STDINT
-	If stdint.h is available with your toolchain you can define this
-	option to enable it. You can provide option 'USE_STDINT=1' when
-	building U-Boot to enable this.
-
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:
@@ -3264,8 +3229,8 @@ Low Level (hardware related) configuration options:
 		a 16 bit bus.
 		Not all NAND drivers use this symbol.
 		Example of drivers that use it:
-		- drivers/mtd/nand/ndfc.c
-		- drivers/mtd/nand/mxc_nand.c
+		- drivers/mtd/nand/raw/ndfc.c
+		- drivers/mtd/nand/raw/mxc_nand.c
 
 - CONFIG_SYS_NDFC_EBC0_CFG
 		Sets the EBC0_CFG register for the NDFC. If not defined
@@ -3382,7 +3347,7 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
 		Option to disable subpage write in NAND driver
 		driver that uses this:
-		drivers/mtd/nand/davinci_nand.c
+		drivers/mtd/nand/raw/davinci_nand.c
 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------