X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;ds=sidebyside;f=include%2Fconfigs%2Fmotionpro.h;h=ab1d9f1651cd2d7870b9fe1e6dd00b19627c4e65;hb=43ade93bdb0c8bd57382be810a05b3793749ce85;hp=e8b05932a13a847ee329181292c11927b6521262;hpb=e97f9d817e600cd6f43d1d0da76f5787e33a5c56;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index e8b0593..ab1d9f1 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -33,23 +33,13 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -72,22 +62,9 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x1b"
-#define DEBUG_BOOTKEYS		0
-#undef CONFIG_AUTOBOOT_DELAY_STR
 #undef CONFIG_BOOTARGS
-#define CONFIG_AUTOBOOT_PROMPT	"Autobooting in %d seconds, "		\
-				"press \"<Esc><Esc>\" to stop\n", bootdelay
 
 #define CONFIG_CMDLINE_EDITING		1	/* add command line history	*/
-#define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#define CONFIG_ETHADDR		00:50:C2:40:10:00
-#define CONFIG_OVERWRITE_ETHADDR_ONCE	1
-#define CONFIG_VERSION_VARIABLE	1	/* include version env variable */
 
 /*
  * Default environment settings
@@ -280,7 +257,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x0060
 #define CONFIG_SYS_ATA_REG_OFFSET	CONFIG_SYS_ATA_DATA_OFFSET
 #define CONFIG_SYS_ATA_STRIDE		4
-#define CONFIG_DOS_PARTITION
 
 /*
  * I2C configuration
@@ -296,7 +272,6 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	1	/* 2 bytes per write cycle */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5	/* 2ms/cycle + 3ms extra */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS		1	/* 2 EEPROMs (addr:50,52) */
 
 /*
  * RTC configuration
@@ -307,24 +282,10 @@
 /*
  * Status LED configuration
  */
-#define CONFIG_STATUS_LED		/* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
 
 #define ENABLE_GPIO_OUT		0x00000024
 #define LED_ON			0x00000010
 
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
 /*
  * Temperature sensor
  */
@@ -389,10 +350,6 @@ extern void __led_set(led_id_t id, int state);
 /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
 #define CONFIG_SYS_RESET_ADDRESS	0xfff00100
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)