X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;ds=sidebyside;f=include%2Fconfigs%2Fluan.h;h=41999d32f97aaa2142080c1bbf7886e97349d3d2;hb=3c1de1a6d36be9eee284a6c596a86e94f19cc5b2;hp=72aae09d03971a831e037b25441c8b45130f7c9c;hpb=6bf6f114dcdd97ec3f80c2761ed40e31229d6b78;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/luan.h b/include/configs/luan.h
index 72aae09..41999d3 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -69,7 +68,6 @@
 #define CFG_FLASH_BASE		CFG_SMALL_FLASH
 #endif
 
-#undef CFG_DRAM_TEST
 #if CFG_SRAM_BASE
 #define CFG_KBYTES_SDRAM	1024*2
 #else
@@ -136,7 +134,6 @@
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
 #define CONFIG_DDR_ECC		1	/* with ECC support		*/
-#define CFG_44x_DDR2_CKTR_180	1	/* use 180 deg advance		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -154,7 +151,7 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
 
 #undef	CONFIG_BOOTARGS
@@ -184,7 +181,7 @@
 	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
 		"cp.b 100000 fffc0000 40000;"			        \
 		"setenv filesize;saveenv\0"				\
-	"upd=run load;run update\0"					\
+	"upd=run load update\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -197,6 +194,7 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_HAS_ETH0
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
@@ -213,7 +211,6 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-
 /*
  * BOOTP options
  */
@@ -222,7 +219,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -230,7 +226,6 @@
 
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
@@ -242,7 +237,6 @@
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-
 /*
  * Miscellaneous configurable options
  */
@@ -299,15 +293,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
@@ -321,4 +306,8 @@
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
 #endif	/* __CONFIG_H */