X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;ds=sidebyside;f=include%2Fconfigs%2Fls2080a_common.h;h=3e86d1bff215c32dc019a9fedf6f845080fa7049;hb=c45568cc4e51b7bbe2f3ce28d8f2566048aeebf3;hp=b58776a788b1a39d4c02be451d7cca534ab6a82a;hpb=71d96eb99e79ba69f47504b72cd54ce121eca422;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index b58776a..3e86d1b 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -7,29 +7,15 @@
 #ifndef __LS2_COMMON_H
 #define __LS2_COMMON_H
 
-#define CONFIG_REMAKE_ELF
-#define CONFIG_GICV3
-
 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>
 
 /* Link Definitions */
-#ifdef CONFIG_TFABOOT
-#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
-#else
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#endif
 
 /* We need architecture specific misc initializations */
 
 /* Link Definitions */
 
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_DDR_RAW_TIMING
-#endif
-
 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
 
 #define CONFIG_VERY_BIG_RAM
@@ -42,45 +28,24 @@
 /*
  * SMP Definitinos
  */
-#define CPU_RELEASE_ADDR		secondary_boot_func
+#define CPU_RELEASE_ADDR		secondary_boot_addr
 
 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
-#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
-#define CONFIG_SYS_DP_DDR_BASE		0x6000000000ULL
-/*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
-#define CONFIG_SYS_DP_DDR_BASE_PHY	0
-#define CONFIG_DP_DDR_CTRL		2
-#define CONFIG_DP_DDR_NUM_CTRLS		1
-#endif
 
-/* Generic Timer Definitions */
 /*
  * This is not an accurate number. It is used in start.S. The frequency
  * will be udpated later when get_bus_freq(0) is available.
  */
-#define COUNTER_FREQUENCY		25000000	/* 25MHz */
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)
+/* GPIO */
 
 /* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#endif
 
 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-/* IFC */
-#define CONFIG_FSL_IFC
-
 /*
  * During booting, IFC is mapped at the region of 0x30000000.
  * But this region is limited to 256MB. To accommodate NOR, promjet
@@ -134,11 +99,6 @@ unsigned long long get_qixis_addr(void);
 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000
 
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
@@ -149,21 +109,14 @@ unsigned long long get_qixis_addr(void);
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(128UL * 1024 * 1024)
 #endif
 
-/* Command line configuration */
-
 /* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 
 /* Physical Memory Map */
 /* fixme: these need to be checked against the board */
-#define CONFIG_CHIP_SELECTS_PER_CTRL	4
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128
 
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
@@ -180,39 +133,12 @@ unsigned long long get_qixis_addr(void);
 	"mcinitcmd=fsl_mc start mc 0x580a00000"	\
 	" 0x580e00000 \0"
 
-#ifndef CONFIG_TFABOOT
-#ifdef CONFIG_SD_BOOT
-#define CONFIG_BOOTCOMMAND	"mmc read 0x80200000 0x6800 0x800;"\
-				" fsl_mc apply dpl 0x80200000 &&" \
-				" mmc read $kernel_load $kernel_start" \
-				" $kernel_size && bootm $kernel_load"
-#else
-#define CONFIG_BOOTCOMMAND	"fsl_mc apply dpl 0x580d00000 &&" \
-				" cp.b $kernel_start $kernel_load" \
-				" $kernel_size && bootm $kernel_load"
-#endif
-#endif
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
-#define CONFIG_SYS_MAXARGS		64	/* max command args */
-
-#define CONFIG_SPL_BSS_START_ADDR	0x80100000
-#define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
-#define CONFIG_SPL_MAX_SIZE		0x16000
-#define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
-#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
-
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
 #endif
-#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
-#define CONFIG_SYS_SPL_MALLOC_START	0x80200000
 #define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)
 
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
-
 #include <asm/arch/soc.h>
 
 #endif /* __LS2_COMMON_H */