X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;ds=sidebyside;f=include%2Fconfigs%2Fdevkit3250.h;h=2f3a20e9b8cc3dac98d991bdfa7fb2ca275959b4;hb=b0cf733933c3bc1b4ab353e16affabc60f863db5;hp=cc6a53e6753e3b9ec524f88820380b7ee616d7fe;hpb=0741701acf00749672f75f4c196dabd8b235f741;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index cc6a53e..2f3a20e 100644
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -24,7 +24,6 @@
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /*
  * Memory configurations
@@ -33,7 +32,7 @@
 #define CONFIG_SYS_MALLOC_LEN		SZ_1M
 #define CONFIG_SYS_SDRAM_BASE		EMC_DYCS0_BASE
 #define CONFIG_SYS_SDRAM_SIZE		SZ_64M
-#define CONFIG_SYS_TEXT_BASE		0x83FA0000
+#define CONFIG_SYS_TEXT_BASE		0x83F00000
 #define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + SZ_32K)
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_TEXT_BASE - SZ_1M)
 
@@ -49,25 +48,29 @@
 #define CONFIG_BAUDRATE			115200
 
 /*
+ * DMA
+ */
+#if !defined(CONFIG_SPL_BUILD)
+#define CONFIG_DMA_LPC32XX
+#endif
+
+/*
  * I2C
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_LPC32XX
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_CMD_I2C
 
 /*
  * GPIO
  */
 #define CONFIG_LPC32XX_GPIO
-#define CONFIG_CMD_GPIO
 
 /*
  * SSP/SPI
  */
 #define CONFIG_LPC32XX_SSP
 #define CONFIG_LPC32XX_SSP_TIMEOUT	100000
-#define CONFIG_CMD_SPI
 
 /*
  * Ethernet
@@ -78,9 +81,6 @@
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_ADDR			0x1F
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
 
 /*
  * NOR Flash
@@ -111,10 +111,20 @@
 #define CONFIG_LPC32XX_NAND_SLC_RHOLD		200000000
 #define CONFIG_LPC32XX_NAND_SLC_RSETUP		50000000
 
+#define CONFIG_SYS_NAND_BLOCK_SIZE		0x20000
+#define CONFIG_SYS_NAND_PAGE_SIZE		NAND_LARGE_BLOCK_PAGE_SIZE
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
+
+#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NAND
 
 /*
+ * USB
+ */
+#define CONFIG_USB_OHCI_LPC32XX
+#define CONFIG_USB_ISP1301_I2C_ADDR		0x2d
+
+/*
  * U-Boot General Configurations
  */
 #define CONFIG_SYS_LONGHELP
@@ -126,14 +136,10 @@
 
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
 
 /*
  * Pass open firmware flat tree
  */
-#define CONFIG_OF_LIBFDT
 
 /*
  * Environment
@@ -161,15 +167,12 @@
 /*
  * U-Boot Commands
  */
-#define CONFIG_CMD_CACHE
 
 /*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_BOOTDELAY		1
 
 #define CONFIG_BOOTFILE			"uImage"
 #define CONFIG_BOOTARGS			"console=ttyS0,115200n8"
@@ -187,29 +190,14 @@
 
 /* Use the framework and generic lib */
 #define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
 
 /* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
 
 /* SPL loads an image from NAND */
 #define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_NAND_RAW_ONLY
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_DRIVERS
 
-#define CONFIG_SYS_NAND_BLOCK_SIZE	0x20000
-#define CONFIG_SYS_NAND_PAGE_SIZE	0x800
-#define CONFIG_SYS_NAND_ECCSIZE		0x100
-#define CONFIG_SYS_NAND_OOBSIZE		64
-#define CONFIG_SYS_NAND_ECCPOS		{ 40, 41, 42, 43, 44, 45, 46, 47, \
-					  48, 49, 50, 51, 52, 53, 54, 55, \
-					  56, 57, 58, 59, 60, 61, 62, 63, }
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_PAGE_COUNT	64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
-
 #define CONFIG_SPL_NAND_ECC
 #define CONFIG_SPL_NAND_SOFTECC