<info>
<keywords>
A newline-separated list of keywords describing what this test case uses and
-tests. Try to use an already used keyword. These keywords will be used for
-statistical/informational purposes.
+tests. Try to use an already used keyword. These keywords will be used for
+statistical/informational purposes and for choosing or skipping classes
+of tests. "Keywords" must begin with an alphabetic character, "-", "["
+or "{" and may actually consist of multiple words separated by spaces
+which are treated together as a single identifier.
</keywords>
</info>
<reply>
-<data [nocheck="1"] [sendzero="yes"] [base64="yes"]>
+<data [nocheck="yes"] [sendzero="yes"] [base64="yes"]>
data to be sent to the client on its request and later verified that it arrived
-safely. Set the nocheck=1 to prevent the test script to verify the arrival
+safely. Set nocheck="yes" to prevent the test script from verifying the arrival
of this data.
If the data contains 'swsclose' anywhere within the start and end tag, and
of data encoded with base64. It is the only way a test case can contain binary
data. (This attribute can in fact be used on any section, but it doesn't make
much sense for other sections than "data").
+
+For FTP file listings, the <data> section will be used *only* if you make sure
+that there has been a CWD done first to a directory named 'test-[num]' where
+[num] is the test case number. Otherwise the ftp server can't know from which
+test file to load the list content.
+
</data>
<dataNUM>
Send back this contents instead of the <data> one. The num is set by:
B) The request was HTTP and included digest details, which adds 1000 to NUM
C) If a HTTP request is NTLM type-1, it adds 1001 to num
D) If a HTTP request is NTLM type-3, it adds 1002 to num
+E) If a HTTP request is Basic and num is already >=1000, it adds 1 to num
+
+Dynamically changing num in this way allows the test harness to be used to
+test authentication negotiation where several different requests must be sent
+to complete a transfer. The response to each request is found in its own data
+section. Validating the entire negotiation sequence can be done by
+specifying a datacheck section.
</dataNUM>
+<connect>
+The connect section is used instead of the 'data' for all CONNECT
+requests. The remainder of the rules for the data section then apply but with
+a connect prefix.
+</connect>
<datacheck [nonewline="yes"]>
if the data is sent but this is what should be checked afterwards. If
'nonewline' is set, we will cut off the trailing newline of this given data
</postcmd>
<servercmd>
Special-commands for the server.
-For FTP, these are supported:
+For FTP/SMTP/POP/IMAP, these are supported:
REPLY [command] [return value] [response string]
- Changes how the server responds to the [command]. [response string] is
evaluated as a perl string, so it can contain embedded \r\n, for example.
+ There's a special [command] named "welcome" (without quotes) which is the
+ string sent immediately on connect as a welcome.
COUNT [command] [num]
- Do the REPLY change for [command] only [num] times and then go back to the
built-in approach
NOSAVE
- Don't actually save what is received
SLOWDOWN
- - Send FTP responses with 0.1 sec delay between each byte
+ - Send FTP responses with 0.01 sec delay between each byte
PASVBADIP
- makes PASV send back an illegal IP in its 227 response
+CAPA [capabilities]
+ - Enables support for and specifies a list of space separated capabilities to
+ return to the client for the IMAP CAPABILITY, POP3 CAPA and SMTP EHLO
+ commands
+AUTH [mechanisms]
+ - Enables support for SASL authentication and specifies a list of space
+ separated mechanisms for IMAP, POP3 and SMTP
For HTTP/HTTPS:
-auth_required - if this is set and a POST/PUT is made without auth, the
+auth_required if this is set and a POST/PUT is made without auth, the
server will NOT wait for the full request body to get sent
-idle - do nothing after receiving the request, just "sit idle"
-stream - continuously send data to the client, never-ending
-pipe: [num] - tell the server to expect this many HTTP requests before
+idle do nothing after receiving the request, just "sit idle"
+stream continuously send data to the client, never-ending
+writedelay: [secs] delay this amount between reply packets
+pipe: [num] tell the server to expect this many HTTP requests before
sending back anything, to allow pipelining tests
+skip: [num] instructs the server to ignore reading this many bytes from a PUT
+ or POST request
+
+rtp: part [num] channel [num] size [num]
+ stream a fake RTP packet for the given part on a chosen channel
+ with the given payload size
+
+connection-monitor When used, this will log [DISCONNECT] to the server.input
+ log when the connection is disconnected.
+
+
+For TFTP:
+writedelay: [secs] delay this amount between reply packets (each packet being
+ 512 bytes payload)
</servercmd>
</reply>
ftps
http
http-ipv6
+http-proxy
https
+httptls+srp
+httptls+srp-ipv6
+imap
none
+pop3
+rtsp
+rtsp-ipv6
scp
sftp
+smtp
socks4
socks5
be able to run (if these features are not present, the test will be
SKIPPED). Features testable here are:
+axTLS
crypto
+debug
getrlimit
GnuTLS
idn
ipv6
large_file
libz
-netrc_debug
+Metalink
NSS
+NTLM
OpenSSL
+socks
SSL
+TLS-SRP
+TrackMemory
+unittest
as well as each protocol that curl supports. A protocol only needs to be
specified if it is different from the server (useful when the server
<precheck>
A command line that if set gets run by the test script before the test. If an
-output is displayed by the command, the test will be skipped and the
-(single-line) output will be displayed as reason for not running the test.
-Variables are substituted as in the <command> section.
+output is displayed by the command or if the return code is non-zero, the test
+will be skipped and the (single-line) output will be displayed as reason for
+not running the test. Variables are substituted as in the <command> section.
</precheck>
<postcheck>
<tool>
Name of tool to use instead of "curl". This tool must be built and exist
-in the libtest/ directory.
+either in the libtest/ directory (if the tool starts with 'lib') or in the
+unit/ directory (if the tool starts with 'unit').
</tool>
<name>
Variables are first substituted as in the <command> section.
</setenv>
-<command [option="no-output"]>
+<command [option="no-output/no-include"] [timeout="secs"] [delay="secs"]
+ [type="perl"]>
command line to run, there's a bunch of %variables that get replaced
accordingly.
number (N) will be used by the test-server to load test case N and return the
data that is defined within the <reply><data></data></reply> section.
-If a CONNECT is used to the server (to emulate HTTPS etc over proxy), the port
-number given in the CONNECT request will be used to identify which test that
-is being run, if the proxy host name is said to start with 'test'.
+If there's no test number found above, the HTTP test server will use the
+number following the last dot in the given hostname (made so that a CONNECT
+can still pass on test number) so that "foo.bar.123" gets treated as test case
+123. Alternatively, if an ipv6-address is provided to CONNECT, the last
+hexadecimal group in the address will be used as the test numer! For example
+the address "[1234::ff]" would be treated as test case 255.
-Set 'option=no-output' to prevent the test script to slap on the --output
+Set type="perl" to write the test case as a perl script. It implies that
+there's no memory debugging and valgrind gets shut off for this test.
+
+Set option="no-output" to prevent the test script to slap on the --output
argument that directs the output to a file. The --output is also not added if
-the client/stdout section is used.
+the verify/stdout section is used.
+
+Set option="no-include" to prevent the test script to slap on the --include
+argument.
+
+Set timeout="secs" to override default server logs advisor read lock timeout.
+This timeout is used by the test harness, once that the command has completed
+execution, to wait for the test server to write out server side log files and
+remove the lock that advised not to read them. The "secs" parameter is the not
+negative integer number of seconds for the timeout. This 'timeout' attribute
+is documented for completeness sake, but is deep test harness stuff and only
+needed for very singular and specific test cases. Avoid using it.
+
+Set delay="secs" to introduce a time delay once that the command has completed
+execution and before the <postcheck> section runs. The "secs" parameter is the
+not negative integer number of seconds for the delay. This 'delay' attribute
+is intended for very specific test cases, and normally not needed.
Available substitute variables include:
-%HOSTIP - IPv6 address of the host running this test
-%HOSTPORT - Port number of the HTTP server
-%HOST6IP - IPv6 address of the host running this test
-%HOST6PORT - IPv6 port number of the HTTP server
-%HTTPSPORT - Port number of the HTTPS server
-%FTPPORT - Port number of the FTP server
+%CLIENT6IP - IPv6 address of the client running curl
+%CLIENTIP - IPv4 address of the client running curl
+%CURL - Path to the curl executable
+%FTP2PORT - Port number of the FTP server 2
%FTP6PORT - IPv6 port number of the FTP server
+%FTPPORT - Port number of the FTP server
%FTPSPORT - Port number of the FTPS server
-%FTP2PORT - Port number of the FTP server 2
%FTPTIME2 - Timeout in seconds that should be just sufficient to receive
a response from the test FTP server
-%TFTPPORT - Port number of the TFTP server
-%TFTP6PORT - IPv6 port number of the TFTP server
-%SSHPORT - Port number of the SCP/SFTP server
+%FTPTIME3 - Even longer than %FTPTIME2
+%GOPHER6PORT - IPv6 port number of the Gopher server
+%GOPHERPORT - Port number of the Gopher server
+%HOST6IP - IPv6 address of the host running this test
+%HOSTIP - IPv4 address of the host running this test
+%HTTP6PORT - IPv6 port number of the HTTP server
+%HTTPPIPEPORT - Port number of the HTTP pipelining server
+%HTTPPORT - Port number of the HTTP server
+%HTTPSPORT - Port number of the HTTPS server
+%HTTPTLS6PORT - IPv6 port number of the HTTP TLS server
+%HTTPTLSPORT - Port number of the HTTP TLS server
+%IMAP6PORT - IPv6 port number of the IMAP server
+%IMAPPORT - Port number of the IMAP server
+%POP36PORT - IPv6 ort number of the POP3 server
+%POP3PORT - Port number of the POP3 server
+%PROXYPORT - Port number of the HTTP proxy
+%PWD - Current directory
+%RTSP6PORT - IPv6 port number of the RTSP server
+%RTSPPORT - Port number of the RTSP server
+%SMTP6PORT - IPv6 port number of the SMTP server
+%SMTPPORT - Port number of the SMTP server
%SOCKSPORT - Port number of the SOCKS4/5 server
%SRCDIR - Full path to the source dir
-%PWD - Current directory
-%CURL - Path to the curl executable
+%SSHPORT - Port number of the SCP/SFTP server
+%TFTP6PORT - IPv6 port number of the TFTP server
+%TFTPPORT - Port number of the TFTP server
%USER - Login ID of the user running the test
</command>
section.
</file>
-<stdin>
+<stdin [nonewline="yes"]>
Pass this given data on stdin to the tool.
+
+If 'nonewline' is set, we will cut off the trailing newline of this given data
+before comparing with the one actually received by the client
</stdin>
</client>
One perl op per line that operates on the protocol dump. This is pretty
advanced. Example: "s/^EPRT .*/EPRT stripped/"
</strippart>
+
<protocol [nonewline="yes"]>
-the protocol dump curl should transmit, if 'nonewline' is set, we will cut
-off the trailing newline of this given data before comparing with the one
-actually sent by the client
-Variables are substituted as in the <command> section.
+
+the protocol dump curl should transmit, if 'nonewline' is set, we will cut off
+the trailing newline of this given data before comparing with the one actually
+sent by the client Variables are substituted as in the <command> section. The
+<strip> and <strippart> rules are applied before comparisons are made.
+
</protocol>
-<stdout [mode="text"]>
-This verifies that this data was passed to stdout.
+
+<proxy [nonewline="yes"]>
+
+The protocol dump curl should transmit to a HTTP proxy (when the http-proxy
+server is used), if 'nonewline' is set, we will cut off the trailing newline
+of this given data before comparing with the one actually sent by the client
+Variables are substituted as in the <command> section. The <strip> and
+<strippart> rules are applied before comparisons are made.
+
+</proxy>
+
+<stdout [mode="text"] [nonewline="yes"]>
+This verifies that this data was passed to stdout. Variables are
+substituted as in the <command> section.
Use the mode="text" attribute if the output is in text mode on platforms that
have a text/binary difference.
+
+If 'nonewline' is set, we will cut off the trailing newline of this given data
+before comparing with the one actually received by the client
</stdout>
<file name="log/filename" [mode="text"]>
The file's contents must be identical to this after the test is complete.
-
Use the mode="text" attribute if the output is in text mode on platforms that
have a text/binary difference.
+Variables are substituted as in the <command> section.
</file>
<stripfile>
One perl op per line that operates on the file before being compared. This is
projects / platform / upstream / curl.git / blobdiff