# the scan list is empty. In that case, a simple backoff
# mechanism starting from 10s up to 5 minutes will run.
# BackgroundScanning = true
+BackgroundScanning = false
# List of Fallback timeservers separated by ",".
# These timeservers are used for NTP sync when there are
# These can contain mixed combination of fully qualified
# domain names, IPv4 and IPv6 addresses.
# FallbackTimeservers =
+#FallbackTimeservers = pool.ntp.org
-# List of fallback nameservers separated by "," appended
-# to the list of nameservers given by the service. The
+# List of fallback nameservers separated by "," used if no
+# nameservers are otherwise provided by the service. The
# nameserver entries must be in numeric format, host
# names are ignored.
# FallbackNameservers =
# the default route when compared to either a non-preferred
# type or a preferred type further down in the list.
# PreferredTechnologies =
+PreferredTechnologies = wifi, ethernet
# List of blacklisted network interfaces separated by ",".
# Found interfaces will be compared to the list and will
# not be handled by connman, if their first characters
# match any of the list entries. Default value is
-# vmnet,vboxnet,virbr.
-# NetworkInterfaceBlacklist = vmnet,vboxnet,virbr
+# vmnet,vboxnet,virbr,ifb,ve-,vb-.
+# NetworkInterfaceBlacklist = vmnet,vboxnet,virbr,ifb,ve-,vb-
+NetworkInterfaceBlacklist = veth, vmnet,vboxnet,virbr,usb,rndis,rmnet,rev_rmnet,dummy,seth_td,seth_w
# Allow connman to change the system hostname. This can
# happen for example if we receive DHCP hostname option.
# Default value is true.
# AllowHostnameUpdates = true
+
+# Keep only a single connected technology at any time. When a new
+# service is connected by the user or a better one is found according
+# to PreferredTechnologies, the new service is kept connected and all
+# the other previously connected services are disconnected. With this
+# setting it does not matter whether the previously connected services
+# are in 'online' or 'ready' states, the newly connected service is
+# the only one that will be kept connected. A service connected by the
+# user will be used until going out of network coverage. With this
+# setting enabled applications will notice more network breaks than
+# normal. Default value is false.
+# SingleConnectedTechnology = false
+SingleConnectedTechnology = true
+
+# List of technologies for which tethering is allowed separated by ",".
+# The default value is wifi,bluetooth,gadget. Only those technologies
+# listed here are used for tethering. If ethernet tethering is desired,
+# then ethernet should be added to the list. The technologies listed here
+# have to support tethering, currently tethering is implemented for wifi,
+# bluetooth, gadget and ethernet.
+# NOTE that if ethernet tethering is enabled, then a DHCP server is
+# started on all ethernet interfaces. Tethered ethernet should
+# never be connected to corporate or home network as it will disrupt
+# normal operation of these networks. Due to this ethernet is not
+# tethered by default. Do not activate ethernet tethering unless you
+# really know what you are doing.
+# TetheringTechnologies = wifi,bluetooth,gadget
+
+# Restore earlier tethering status when returning from offline mode,
+# re-enabling a technology, and after restarts and reboots.
+# Default value is false.
+# PersistentTetheringMode = false
+
+# Automatically enable Anycast 6to4 if possible. This is not recommended, as
+# the use of 6to4 will generally lead to a severe degradation of connection
+# quality. See RFC6343. Default value is false (as recommended by RFC6343
+# section 4.1).
+# Enable6to4 = false
+
+# Enable use of http get as on online status check.
+# When a service is in a READY state, and is selected as default,
+# ConnMan will issue an HTTP GET request to verify that end-to-end
+# connectivity is successful. Only then the service will be
+# transitioned to ONLINE state.
+# If this setting is false, the default service will remain in READY state.
+# Default value is true.
+# EnableOnlineCheck = false
+
+# List of technologies with AutoConnect = true which are always connected
+# regardless of PreferredTechnologies setting. Default value is empty and
+# will connect a technology only if it is at a higher preference than any
+# other which is already connected.
+# This setting has no effect if SingleConnectedTechnologies is enabled.
+# AlwaysConnectedTechnologies =
+
+NetworkCellularInterfaceList = pdp,rmnet,seth_td,seth_w