+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2012 SAMSUNG Electronics
* Jaehoon Chung <jh80.chung@samsung.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __DWMMC_HW_H
#define DWMCI_INTMSK_DTO (1 << 3)
#define DWMCI_INTMSK_TXDR (1 << 4)
#define DWMCI_INTMSK_RXDR (1 << 5)
+#define DWMCI_INTMSK_RCRC (1 << 6)
#define DWMCI_INTMSK_DCRC (1 << 7)
#define DWMCI_INTMSK_RTO (1 << 8)
#define DWMCI_INTMSK_DRTO (1 << 9)
#define DWMCI_CTYPE_8BIT (1 << 16)
/* Status Register */
+#define DWMCI_FIFO_EMPTY (1 << 2)
+#define DWMCI_FIFO_FULL (1 << 3)
#define DWMCI_BUSY (1 << 9)
-#define DWMCI_FIFO_MASK 0x1ff
+#define DWMCI_FIFO_MASK 0x1fff
#define DWMCI_FIFO_SHIFT 17
/* FIFOTH Register */
return readb(host->ioaddr + reg);
}
-void dwmci_setup_cfg(struct mmc_config *cfg, const char *name, int buswidth,
- uint caps, u32 max_clk, u32 min_clk);
+#ifdef CONFIG_BLK
+/**
+ * dwmci_setup_cfg() - Set up the configuration for DWMMC
+ *
+ * This is used to set up a DWMMC device when you are using CONFIG_BLK.
+ *
+ * This should be called from your MMC driver's probe() method once you have
+ * the information required.
+ *
+ * Generally your driver will have a platform data structure which holds both
+ * the configuration (struct mmc_config) and the MMC device info (struct mmc).
+ * For example:
+ *
+ * struct rockchip_mmc_plat {
+ * struct mmc_config cfg;
+ * struct mmc mmc;
+ * };
+ *
+ * ...
+ *
+ * Inside U_BOOT_DRIVER():
+ * .platdata_auto_alloc_size = sizeof(struct rockchip_mmc_plat),
+ *
+ * To access platform data:
+ * struct rockchip_mmc_plat *plat = dev_get_platdata(dev);
+ *
+ * See rockchip_dw_mmc.c for an example.
+ *
+ * @cfg: Configuration structure to fill in (generally &plat->mmc)
+ * @host: DWMMC host
+ * @max_clk: Maximum supported clock speed in HZ (e.g. 150000000)
+ * @min_clk: Minimum supported clock speed in HZ (e.g. 400000)
+ */
+void dwmci_setup_cfg(struct mmc_config *cfg, struct dwmci_host *host,
+ u32 max_clk, u32 min_clk);
+
+/**
+ * dwmci_bind() - Set up a new MMC block device
+ *
+ * This is used to set up a DWMMC block device when you are using CONFIG_BLK.
+ * It should be called from your driver's bind() method.
+ *
+ * See rockchip_dw_mmc.c for an example.
+ *
+ * @dev: Device to set up
+ * @mmc: Pointer to mmc structure (normally &plat->mmc)
+ * @cfg: Empty configuration structure (generally &plat->cfg). This is
+ * normally all zeroes at this point. The only purpose of passing
+ * this in is to set mmc->cfg to it.
+ * @return 0 if OK, -ve if the block device could not be created
+ */
int dwmci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg);
+#else
+/**
+ * add_dwmci() - Add a new DWMMC interface
+ *
+ * This is used when you are not using CONFIG_BLK. Convert your driver over!
+ *
+ * @host: DWMMC host structure
+ * @max_clk: Maximum supported clock speed in HZ (e.g. 150000000)
+ * @min_clk: Minimum supported clock speed in HZ (e.g. 400000)
+ * @return 0 if OK, -ve on error
+ */
int add_dwmci(struct dwmci_host *host, u32 max_clk, u32 min_clk);
+#endif /* !CONFIG_BLK */
+
+#ifdef CONFIG_DM_MMC
+/* Export the operations to drivers */
+int dwmci_probe(struct udevice *dev);
+extern const struct dm_mmc_ops dm_dwmci_ops;
+#endif
+
#endif /* __DWMMC_HW_H */