#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
+/* GUIDs for capsule updatable firmware images */
+#define XILINX_BOOT_IMAGE_GUID \
+ EFI_GUID(0x1ba29a15, 0x9969, 0x40aa, 0xb4, 0x24, \
+ 0xe8, 0x61, 0x21, 0x61, 0x86, 0x64)
+
+#define XILINX_UBOOT_IMAGE_GUID \
+ EFI_GUID(0x1a5178f0, 0x87d3, 0x4f36, 0xac, 0x63, \
+ 0x3b, 0x31, 0xa2, 0x3b, 0xe3, 0x05)
+
/* Serial drivers */
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/* Ethernet driver */
-#if defined(CONFIG_ZYNQ_GEM)
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#endif
/* NOR */
#ifdef CONFIG_MTD_NOR_FLASH
/* Miscellaneous configurable options */
-#define CONFIG_CLOCKS
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-#define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */
-
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
/* Extend size of kernel image for uncompression */
/* Boot FreeBSD/vxWorks from an ELF image */
#define CONFIG_SYS_MMC_MAX_DEVICE 1
-/* MMC support */
-#ifdef CONFIG_MMC_SDHCI_ZYNQ
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#endif
-
/* Address in RAM where the parameters must be copied by SPL. */
#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
-#define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb"
-#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
-
/* Not using MMC raw mode - just for compilation purpose */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
/* SP location before relocation, must use scratch RAM */
/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
-#define CONFIG_SPL_MAX_SIZE 0x30000
/* On the top of OCM space */
#define CONFIG_SYS_SPL_MALLOC_START CONFIG_SPL_STACK_R_ADDR
* 0xfffffe00 is used for putting wfi loop.
* Set it up as limit for now.
*/
-#define CONFIG_SPL_STACK 0xfffffe00
/* BSS setup */
#define CONFIG_SPL_BSS_START_ADDR 0x100000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x100000
#endif /* __CONFIG_ZYNQ_COMMON_H */