#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG
-#undef DEBUG
-
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
#define EXTCLK_50 50000000
#define EXTCLK_83 83333333
-#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#undef CONFIG_SHOW_BOOT_PROGRESS
#undef CONFIG_STRESS
-#undef ENABLE_ECC
+
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 0x90000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE2 0xa0000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE3 0xb0000000 /* mapped pci memory */
-
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_PCI_TARGBASE 0x80000000 /*PCIaddr mapped to CFG_PCI_MEMBASE*/
+#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
+
+#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
+#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
-/* #define CFG_PCI_BASE_IO 0xB8000000 */ /* internal PCI I-O */
-/* #define CFG_PCI_BASE_REGS 0xBEC00000 */ /* internal PCI regs */
-/* #define CFG_PCI_BASE_CYCLE 0xBED00000 */ /* internal PCI regs */
+#define CFG_PCIE0_CFGBASE 0xc0000000
+#define CFG_PCIE1_CFGBASE 0xc1000000
+#define CFG_PCIE2_CFGBASE 0xc2000000
+#define CFG_PCIE0_XCFGBASE 0xc3000000
+#define CFG_PCIE1_XCFGBASE 0xc3001000
+#define CFG_PCIE2_XCFGBASE 0xc3002000
/* System RAM mapped to PCI space */
#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
-#define SPD_EEPROM_ADDRESS {0x53, 0x52} /* SPD i2c spd addresses */
-#define IIC0_DIMM0_ADDR 0x53
-#define IIC0_DIMM1_ADDR 0x52
+#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS {0x53, 0x52} /* SPD i2c spd addresses*/
+#define CONFIG_DDR_ECC 1 /* with ECC support */
/*-----------------------------------------------------------------------
* I2C
/* Don't probe these addrs */
#define CFG_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54}
-/* #if (CONFIG_COMMANDS & CFG_CMD_EEPROM) */
+/* #if defined(CONFIG_CMD_EEPROM) */
/* #define CFG_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */
#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
/* #endif */
"bootfile=yucca/uImage\0" \
"kernel_addr=E7F10000\0" \
"ramdisk_addr=E7F20000\0" \
+ "initrd_high=30000000\0" \
"load=tftp 100000 yuca/u-boot.bin\0" \
"update=protect off 2:4-7;era 2:4-7;" \
"cp.b ${fileaddr} FFFB0000 ${filesize};" \
"setenv filesize;saveenv\0" \
"upd=run load;run update\0" \
+ "pciconfighost=1\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_EEPROM | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+
+#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#undef CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT /* let board init pci target */
#undef CFG_PCI_MASTER_INIT
*/
/* Support for Intel 82557/82559/82559ER chips. */
#define CONFIG_EEPRO100
+
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
*/
#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define FPGA_REG1C_PE1_WAKE 0x0040
#define FPGA_REG1C_PE2_WAKE 0x0020
#define FPGA_REG1C_PE0_PERST 0x0010
-#define FPGA_REG1C_PE1_PERST 0x0080
-#define FPGA_REG1C_PE2_PERST 0x0040
+#define FPGA_REG1C_PE1_PERST 0x0008
+#define FPGA_REG1C_PE2_PERST 0x0004
/*----------------------------------------------------------------------------+
| Defines