* differences.
*/
-/*=====================*/
-/* Board and Processor */
-/*=====================*/
-
-#define CONFIG_XTFPGA
-
-/* FPGA CPU freq after init */
-#define CONFIG_SYS_CLK_FREQ (gd->cpu_clk)
-
/*===================*/
/* RAM Layout */
/*===================*/
# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */
#endif
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */
-
-/* Linux boot param area in RAM (used only when booting linux) */
-#define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10)
-
/* Memory test is destructive so default must not overlap vectors or U-Boot*/
-#define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000)
-#define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000)
/* Load address for stand-alone applications.
* MEMADDR cannot be used here, because the definition needs to be
#define XTENSA_SYS_TEXT_ADDR \
(MEMADDR(CONFIG_SYS_MEMORY_SIZE) - CONFIG_SYS_MONITOR_LEN)
-/* Used by tftpboot; env var 'loadaddr' */
-#define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000)
-
/*==============================*/
/* U-Boot general configuration */
/*==============================*/
-#define CONFIG_BOARD_POSTCLK_INIT
-
-#define CONFIG_BOOTFILE "uImage"
/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 1024
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
/*==============================*/
/* U-Boot autoboot configuration */
/*==============================*/
-#define CONFIG_MX_CYCLIC
-#define CONFIG_SHOW_BOOT_PROGRESS
-
/*=========================================*/
/* FPGA Registers (board info and control) */
#define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */
/* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_NS16550_CLK get_board_sys_clk()
/*======================*/
/* Ethernet Driver Info */
/* Flash & Environment */
/*=====================*/
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER /* use generic CFI driver */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
#ifdef CONFIG_XTFPGA_LX60
# define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* block size 64KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
-# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#elif defined(CONFIG_XTFPGA_KC705)
# define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000)
-# define CONFIG_SYS_MONITOR_BASE IOADDR(0x06000000)
#else
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
-# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#endif
#define CONFIG_SYS_MAX_FLASH_SECT \
(CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
-#define CONFIG_SYS_FLASH_PROTECTION /* hw flash protection */
/*
* Put environment in top block (64kB)
* Another option would be to put env. in 2nd param block offs 8KB, size 8KB
*/
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
-#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
/* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_EMPTY_INFO