Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board

[platform/kernel/u-boot.git] / include / configs / xpedite550x.h

diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index 3c6bf5c..87c894c 100644 (file)
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -67,7 +67,7 @@
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
-#define SPD_EEPROM_ADDRESS1                    0x54
+#define SPD_EEPROM_ADDRESS                     0x54
 #define SPD_EEPROM_OFFSET              0x200   /* OFFSET of SPD in EEPROM */
 #define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
@@ -93,14 +93,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BTB                     /* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS       1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xef000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
@@ -216,8 +210,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_INIT_RAM_ADDR       0xe0000000
 #define CONFIG_SYS_INIT_RAM_SIZE               0x00004000
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)    /* Reserve 512 KB for Mon */
@@ -340,12 +333,21 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_TSEC_TBI
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
 #define CONFIG_ETHPRIME                "eTSEC2"
 
+/*
+ * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
+ * 1000mbps SGMII link
+ */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+               TBICR_PHY_RESET \
+               | TBICR_FULL_DUPLEX \
+               | TBICR_SPEED1_SET \
+               )
+
 #define CONFIG_TSEC1           1
 #define CONFIG_TSEC1_NAME      "eTSEC1"
 #define TSEC1_FLAGS            (TSEC_GIGABIT | TSEC_REDUCED)
@@ -433,12 +435,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
 
 /*
- * Boot Flags
- */
-#define BOOTFLAG_COLD          0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM          0x02            /* Software reboot */
-
-/*
  * Environment Configuration
  */
 #define CONFIG_ENV_IS_IN_FLASH 1