* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_PXA250 1 /* This is an PXA255 CPU */
+#define CONFIG_CPU_PXA25X 1 /* This is an PXA255 CPU */
#define CONFIG_XAENIAX 1 /* on a xaeniax board */
+#define CONFIG_SYS_TEXT_BASE 0x0
+#define CONFIG_BOARD_LATE_INIT
-#define BOARD_LATE_INIT 1
-
-
-#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_DCACHE_OFF
/*
* select serial console configuration
*/
+#define CONFIG_PXA_SERIAL
#define CONFIG_BTUART 1 /* we use BTUART on XAENIAX */
-
+#define CONFIG_CONS_INDEX 4
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* valid baudrates */
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & ~CFG_CMD_DTT) | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_NFS | \
- CFG_CMD_SDRAM | \
- CFG_CMD_SNTP )
+#undef CONFIG_CMD_DTT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_BOOTCOMMAND "bootm 0x00100000"
#define CONFIG_BOOTARGS "console=ttyS1,115200"
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
* Size of malloc() pool; this lives below the uppermost 128 KiB which are
* used for the RAM copy of the uboot code
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_HUSH_PARSER 1
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER 1
-#define CFG_PROMPT_HUSH_PS2 "> "
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT "u-boot$ " /* Monitor Command Prompt */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "u-boot$ " /* Monitor Command Prompt */
#else
-#define CFG_PROMPT "u-boot=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "u-boot=> " /* Monitor Command Prompt */
#endif
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1
-
-#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0xa1000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0xa1000000 /* default load address */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x141 /* set core clock to 400/200/100 MHz */
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_CPUSPEED 0x141 /* set core clock to 400/200/100 MHz */
/*
* Physical Memory Map
#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */
#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */
-#define CFG_DRAM_BASE 0xa0000000
-#define CFG_DRAM_SIZE 0x04000000
+#define CONFIG_SYS_DRAM_BASE 0xa0000000
+#define CONFIG_SYS_DRAM_SIZE 0x04000000
+
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR 0xfffff800
/*
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ) /* Timeout for Flash Write */
/* FIXME */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x40000)/* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
-
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x40000)/* Addr of Environment Sector */
+#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
/*
* SMSC91C111 Network Card
*/
-#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x10000300 /* chip select 3 */
#define CONFIG_SMC_USE_32_BIT 1 /* 32 bit bus */
#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
* GP82 == NSSPSFRM is 1
* GP83 == NSSPTXD is 1
*/
-#define CFG_GPSR0_VAL 0x8320E420
-#define CFG_GPSR1_VAL 0x00FFAA82
-#define CFG_GPSR2_VAL 0x000DC000
+#define CONFIG_SYS_GPSR0_VAL 0x8320E420
+#define CONFIG_SYS_GPSR1_VAL 0x00FFAA82
+#define CONFIG_SYS_GPSR2_VAL 0x000DC000
/*
* GP03 == LANReset is 0
* GP30 == SDATA_OUT is 0
* GP81 == NSSPCLK is 0
*/
-#define CFG_GPCR0_VAL 0x40C31848
-#define CFG_GPCR1_VAL 0x00000000
-#define CFG_GPCR2_VAL 0x00020000
+#define CONFIG_SYS_GPCR0_VAL 0x40C31848
+#define CONFIG_SYS_GPCR1_VAL 0x00000000
+#define CONFIG_SYS_GPCR2_VAL 0x00020000
/*
* GP00 == CPUWakeUpUSB is input
* GP83 == NSSPTXD is output
* GP84 == NSSPRXD is input
*/
-#define CFG_GPDR0_VAL 0xD3E3FC68
-#define CFG_GPDR1_VAL 0xFCFFAB83
-#define CFG_GPDR2_VAL 0x000FFFFF
+#define CONFIG_SYS_GPDR0_VAL 0xD3E3FC68
+#define CONFIG_SYS_GPDR1_VAL 0xFCFFAB83
+#define CONFIG_SYS_GPDR2_VAL 0x000FFFFF
/*
* GP01 == GP reset is AF01
* GP83 == NSSPTXD is AF01
* GP84 == NSSPRXD is AF10
*/
-#define CFG_GAFR0_L_VAL 0x80000004
-#define CFG_GAFR0_U_VAL 0x595A801A
-#define CFG_GAFR1_L_VAL 0x699A9559
-#define CFG_GAFR1_U_VAL 0xAAA5AAAA
-#define CFG_GAFR2_L_VAL 0xAAAAAAAA
-#define CFG_GAFR2_U_VAL 0x00000256
+#define CONFIG_SYS_GAFR0_L_VAL 0x80000004
+#define CONFIG_SYS_GAFR0_U_VAL 0x595A801A
+#define CONFIG_SYS_GAFR1_L_VAL 0x699A9559
+#define CONFIG_SYS_GAFR1_U_VAL 0xAAA5AAAA
+#define CONFIG_SYS_GAFR2_L_VAL 0xAAAAAAAA
+#define CONFIG_SYS_GAFR2_U_VAL 0x00000256
/*
* clock settings
* BFS = 0
* SSS = 0
*/
-#define CFG_PSSR_VAL 0x00000030
+#define CONFIG_SYS_PSSR_VAL 0x00000030
-#define CFG_CKEN_VAL 0x00000080 /* */
-#define CFG_ICMR_VAL 0x00000000 /* No interrupts enabled */
+#define CONFIG_SYS_CKEN 0x00000080 /* */
+#define CONFIG_SYS_ICMR 0x00000000 /* No interrupts enabled */
+#define CONFIG_SYS_CCCR CCCR_L27|CCCR_M2|CCCR_N10
/*
* [03] 0 - 32 Bit bus width
* [02:00] 010 - burst OF 4 ROM or FLASH
*/
-#define CFG_MSC0_VAL 0x000023D2
+#define CONFIG_SYS_MSC0_VAL 0x000023D2
/* This is the configuration for nCS2/3 -> USB controller, LAN
* configuration for nCS3: LAN
* [03] 1 - 16 Bit bus width
* [02:00] 100 - variable latency I/O
*/
-#define CFG_MSC1_VAL 0x1224A26C
+#define CONFIG_SYS_MSC1_VAL 0x1224A26C
/* This is the configuration for nCS4/5 -> LAN
* configuration for nCS5:
* [03] 0 - 32 Bit bus width
* [02:00] 100 - variable latency I/O
*/
-#define CFG_MSC2_VAL 0x00001224
+#define CONFIG_SYS_MSC2_VAL 0x00001224
/* MDCNFG: SDRAM Configuration Register
*
* [00] 1 - enable SDRAM partition 0
*/
/* use the configuration above but disable partition 0 */
-#define CFG_MDCNFG_VAL 0x00000AC9
+#define CONFIG_SYS_MDCNFG_VAL 0x00000AC9
/* MDREFR: SDRAM Refresh Control Register
*
* [12] 0 - E0PIN: disable SDCKE0
* [11:00] 000000011000 - (64ms/8192)*MemClkFreq/32 = 24
*/
-#define CFG_MDREFR_VAL 0x00138018 /* mh: was 0x00118018 */
+#define CONFIG_SYS_MDREFR_VAL 0x00138018 /* mh: was 0x00118018 */
/* MDMRS: Mode Register Set Configuration Register
*
* [03] 0 - MDADD0: SDRAM0/1 burst Type. Fixed to sequential.
* [02:00] 010 - MDBL0: SDRAM0/1 burst Length. Fixed to 4.
*/
-#define CFG_MDMRS_VAL 0x00320032
+#define CONFIG_SYS_MDMRS_VAL 0x00320032
+
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x00000000
/*
* PCMCIA and CF Interfaces
*/
-#define CFG_MECR_VAL 0x00000000
-#define CFG_MCMEM0_VAL 0x00010504
-#define CFG_MCMEM1_VAL 0x00010504
-#define CFG_MCATT0_VAL 0x00010504
-#define CFG_MCATT1_VAL 0x00010504
-#define CFG_MCIO0_VAL 0x00004715
-#define CFG_MCIO1_VAL 0x00004715
+#define CONFIG_SYS_MECR_VAL 0x00000000
+#define CONFIG_SYS_MCMEM0_VAL 0x00010504
+#define CONFIG_SYS_MCMEM1_VAL 0x00010504
+#define CONFIG_SYS_MCATT0_VAL 0x00010504
+#define CONFIG_SYS_MCATT1_VAL 0x00010504
+#define CONFIG_SYS_MCIO0_VAL 0x00004715
+#define CONFIG_SYS_MCIO1_VAL 0x00004715
#endif /* __CONFIG_H */