#include <config_distro_defaults.h>
#include "mx6_common.h"
-#define CONFIG_SPL_MMC_SUPPORT
#include "imx6_spl.h"
-#define MACH_TYPE_WANDBOARD 4412
-#define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD
+#define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD_IMX6
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_LIBATA
#endif
-/* Command definition */
-#define CONFIG_CMD_BMODE
-
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_PHY_ATHEROS
/* Framebuffer */
-#define CONFIG_VIDEO
+#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
-#define CONFIG_CMD_HDMIDETECT
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
+#endif
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_EXTRA_ENV_SETTINGS \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
- "videoargs=" \
- "setenv nextcon 0; " \
- "if hdmidet; then " \
- "setenv bootargs ${bootargs} " \
- "video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \
- "if=RGB24; " \
- "setenv fbmen fbmem=28M; " \
- "setexpr nextcon ${nextcon} + 1; " \
- "else " \
- "echo - no HDMI monitor;" \
- "fi; " \
- "i2c dev 1; " \
- "if i2c probe 0x10; then " \
- "setenv bootargs ${bootargs} " \
- "video=mxcfb${nextcon}:dev=lcd,800x480@60," \
- "if=RGB666,bpp=32; " \
- "if test 0 -eq ${nextcon}; then " \
- "setenv fbmem fbmem=10M; " \
- "else " \
- "setenv fbmem ${fbmem},10M; " \
- "fi; " \
- "setexpr nextcon ${nextcon} + 1; " \
- "else " \
- "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
- "fi; " \
- "setenv bootargs ${bootargs} ${fbmem}\0" \
"findfdt="\
"if test $board_name = C1 && test $board_rev = MX6Q ; then " \
"setenv fdtfile imx6q-wandboard.dtb; fi; " \