#include <asm/arch/imx-regs.h>
#include <linux/sizes.h>
-#define CONFIG_SPL_MAX_SIZE (148 * 1024)
-#define CONFIG_SYS_MONITOR_LEN SZ_512K
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
-#define CONFIG_SYS_UBOOT_BASE \
+#define CFG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
-#define CONFIG_SYS_BOOTM_LEN SZ_64M
-
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_STACK 0x920000
-#define CONFIG_SPL_BSS_START_ADDR 0x910000
-#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K /* 8 KB */
-#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
-#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K /* 512 KB */
-
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
-#define CONFIG_MALLOC_F_ADDR 0x930000
+#define CFG_MALLOC_F_ADDR 0x930000
/* For RAW image gives a error info not panic */
-#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
#define MEM_LAYOUT_ENV_SETTINGS \
- "fdt_addr_r=0x44000000\0" \
- "kernel_addr_r=0x42000000\0" \
- "ramdisk_addr_r=0x46400000\0" \
- "scriptaddr=0x46000000\0"
+ "fdt_addr_r=0x50200000\0" \
+ "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "kernel_comp_addr_r=0x40200000\0" \
+ "kernel_comp_size=0x08000000\0" \
+ "ramdisk_addr_r=0x50300000\0" \
+ "scriptaddr=0x50280000\0"
/* Enable Distro Boot */
-#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
-#undef CONFIG_ISO_PARTITION
-#else
-#define BOOTENV
-#endif
/* Initial environment variables */
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
BOOTENV \
MEM_LAYOUT_ENV_SETTINGS \
"bootcmd_mfg=fastboot 0\0" \
"boot_file=Image\0" \
+ "boot_script_dhcp=boot.scr\0" \
"console=ttymxc0\0" \
"fdt_addr=0x43000000\0" \
"fdt_board=dev\0" \
"initrd_addr=0x43800000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \
- "\0" \
- "nfsboot=run netargs; dhcp ${loadaddr} ${boot_file}; " \
- "tftp ${fdt_addr} verdin/${fdtfile}; " \
- "booti ${loadaddr} - ${fdt_addr}\0" \
- "setup=setenv setupargs console=${console},${baudrate} " \
- "console=tty1 consoleblank=0 earlycon\0" \
+ "setup=setenv setupargs console=tty1 console=${console},${baudrate} " \
+ "consoleblank=0 earlycon\0" \
"update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
"if test \"$confirm\" = \"y\"; then " \
"setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
"${blkcnt} / 0x200; mmc dev 0 1; mmc write ${loadaddr} 0x2 " \
"${blkcnt}; fi\0"
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE SZ_2M
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+#define CFG_SYS_INIT_RAM_ADDR 0x40000000
+#define CFG_SYS_INIT_RAM_SIZE SZ_2M
#if defined(CONFIG_ENV_IS_IN_MMC)
/* Environment in eMMC, before config block at the end of 1st "boot sector" */
#endif
-#define CONFIG_SYS_SDRAM_BASE 0x40000000
+#define CFG_SYS_SDRAM_BASE 0x40000000
/* SDRAM configuration */
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE SZ_2G /* 2GB DDR */
-/* UART */
-#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE SZ_2K
-#define CONFIG_SYS_MAXARGS 64
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-/* USDHC */
-#define CONFIG_SYS_FSL_USDHC_NUM 2
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
-
-/* ENET */
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_FEC_MXC_PHYADDR 7
-#define FEC_QUIRK_ENET_MAC
-#define IMX_FEC_BASE 0x30BE0000
-
/* USB Configs */
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif /* __VERDIN_IMX8MM_H */