/*
- * (C) Copyright 2003-2006
+ * (C) Copyright 2003-2009
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* See file CREDITS for list of people who contributed to this
* (easy to change)
*/
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
-#define CONFIG_UC101 1 /* UC101 board */
+#define CONFIG_UC101 1 /* UC101 board */
+#define CONFIG_HOSTNAME uc101
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+#endif
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds"
-#define CONFIG_BOARD_EARLY_INIT_R
+#include "manroland/common.h"
+#include "manroland/mpc5200-common.h"
/*
* Serial console configuration
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-#define CONFIG_DOS_PARTITION
-
/*
* BOOTP options
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DISPLAY
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
-
-#if (TEXT_BASE == 0xFFF00000) /* Boot low */
-# define CFG_LOWBOOT 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addwdt=setenv bootargs ${bootargs} wdt=off" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs=tftp 300000 ${bootfile};run nfsargs addip addwdt;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#define CONFIG_MISC_INIT_R 1
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CFG_I2C_EEPROM_ADDR 0x58
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-/* for LM81 */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CFG_I2C_RTC_ADDR 0x51
-
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM81 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
-
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE 0xFF800000
-
-#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */
-#define CFG_MAX_FLASH_SECT 140 /* max num of sects on one chip */
-
-#define CFG_ENV_ADDR (TEXT_BASE+0x40000) /* second sector */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
- (= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_MAX_FLASH_SECT 140
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x4000
-#define CFG_ENV_SECT_SIZE 0x10000
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE 0x10000
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_DEFAULT_MBAR 0x80000000
-
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SRAM_BASE 0x80100000 /* CS 1 */
-#define CFG_DISPLAY_BASE 0x80600000 /* CS 3 */
-#define CFG_IB_MASTER 0xc0510000 /* CS 6 */
-#define CFG_IB_EPLD 0xc0500000 /* CS 7 */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_DDR 1
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x714f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
+#define CONFIG_SYS_IB_MASTER 0xc0510000 /* CS 6 */
+#define CONFIG_SYS_IB_EPLD 0xc0500000 /* CS 7 */
/* SRAM */
-#define SRAM_BASE CFG_SRAM_BASE /* SRAM base address */
-#define SRAM_LEN 0x1fffff
-#define SRAM_END (SRAM_BASE + SRAM_LEN)
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
-#else
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
-#endif
-
-
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
-#endif
-
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_MII 1
+#define CONFIG_SYS_SRAM_SIZE 0x200000
/*
* GPIO configuration
*/
-#define CFG_GPS_PORT_CONFIG 0x4d558044
-
-/*use Hardware WDT */
-#define CONFIG_HW_WATCHDOG
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-/* Enable an alternate, more extensive memory test */
-#define CFG_ALT_MEMTEST
-
-#define CFG_MEMTEST_START 0x00300000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 3 ... 15 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x300000 /* default load address */
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x4d558044
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_MEMTEST_START 0x00300000
+#define CONFIG_SYS_MEMTEST_END 0x00f00000
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
-#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
-#endif
+#define CONFIG_SYS_LOAD_ADDR 0x300000
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG 0x00045D00
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG 0x00045D00
/* 8Mbit SRAM @0x80100000 */
-#define CFG_CS1_START CFG_SRAM_BASE
-#define CFG_CS1_SIZE 0x00100000
-#define CFG_CS1_CFG 0x21D00
+#define CONFIG_SYS_CS1_SIZE 0x00200000
+#define CONFIG_SYS_CS1_CFG 0x21D00
/* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */
-#define CFG_CS3_START CFG_DISPLAY_BASE
-#define CFG_CS3_SIZE 0x00000100
-#define CFG_CS3_CFG 0x00081802
+#define CONFIG_SYS_CS3_START CONFIG_SYS_DISPLAY_BASE
+#define CONFIG_SYS_CS3_SIZE 0x00000100
+#define CONFIG_SYS_CS3_CFG 0x00081802
/* Interbus Master 16 Bit */
-#define CFG_CS6_START CFG_IB_MASTER
-#define CFG_CS6_SIZE 0x00010000
-#define CFG_CS6_CFG 0x00FF3500
+#define CONFIG_SYS_CS6_START CONFIG_SYS_IB_MASTER
+#define CONFIG_SYS_CS6_SIZE 0x00010000
+#define CONFIG_SYS_CS6_CFG 0x00FF3500
/* Interbus EPLD 8 Bit */
-#define CFG_CS7_START CFG_IB_EPLD
-#define CFG_CS7_SIZE 0x00010000
-#define CFG_CS7_CFG 0x00081800
-
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CONFIG_SYS_CS7_START CONFIG_SYS_IB_EPLD
+#define CONFIG_SYS_CS7_SIZE 0x00010000
+#define CONFIG_SYS_CS7_CFG 0x00081800
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-
-#define CONFIG_IDE_PREINIT 1
-/* #define CONFIG_IDE_RESET 1 beispile siehe tqm5200.c */
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CFG_ATA_STRIDE 4
-
-#define CONFIG_ATAPI 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus*/
/*---------------------------------------------------------------------*/
/* Display addresses */
/*---------------------------------------------------------------------*/
-#define CFG_DISP_CHR_RAM (CFG_DISPLAY_BASE + 0x38)
-#define CFG_DISP_CWORD (CFG_DISPLAY_BASE + 0x30)
+#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38)
+#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30)
#endif /* __CONFIG_H */