/*
* (C) Copyright 2002-2005
- * Gary Jennejohn <gj@denx.de>
+ * Gary Jennejohn <garyj@denx.de>
*
* Configuation settings for the TRAB board.
*
* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_ARM920T 1 /* This is an arm920t CPU */
-#define CONFIG_S3C2400 1 /* in a SAMSUNG S3C2400 SoC */
-#define CONFIG_TRAB 1 /* on a TRAB Board */
-#undef CONFIG_TRAB_50MHZ /* run the CPU at 50 MHz */
+#define CONFIG_ARM920T 1 /* This is an arm920t CPU */
+#define CONFIG_S3C24X0 1 /* in a SAMSUNG S3C24x0-type SoC */
+#define CONFIG_S3C2400 1 /* specifically a SAMSUNG S3C2400 SoC */
+#define CONFIG_TRAB 1 /* on a TRAB Board */
+#undef CONFIG_TRAB_50MHZ /* run the CPU at 50 MHz */
/* automatic software updates (see board/trab/auto_update.c) */
#define CONFIG_AUTO_UPDATE 1
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
-#define CS8900_BASE 0x07000300 /* agrees with WIN CE PA */
-#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
+#define CONFIG_NET_MULTI
+#define CONFIG_CS8900 /* we have a CS8900 on-board */
+#define CONFIG_CS8900_BASE 0x07000300 /* agrees with WIN CE PA */
+#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */
#define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on TRAB */
#define CONFIG_HWFLOW /* include RTS/CTS flow control support */
#define CONFIG_SYS_MEMTEST_START 0x0C000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0D000000 /* 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x0CF00000 /* default load address */
-#ifdef CONFIG_TRAB_50MHZ
-/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
-/* it to wrap 100 times (total 1562500) to get 1 sec. */
-/* this should _really_ be calculated !! */
-#define CONFIG_SYS_HZ 1562500
-#else
-/* the PWM TImer 4 uses a counter of 10390 for 10 ms, so we need */
-/* it to wrap 100 times (total 1039000) to get 1 sec. */
-/* this should _really_ be calculated !! */
-#define CONFIG_SYS_HZ 1039000
-#endif
+#define CONFIG_SYS_HZ 1000
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
/* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=0"
/* production flash layout */