+/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
+ * Copyright (C) 2013, 2014, 2017 Markus Niebel <Markus.Niebel@tq-group.com>
*
- * Configuration settings for the TQ Systems TQMa6<Q,S> module.
- *
- * SPDX-License-Identifier: GPL-2.0+
+ * Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module.
*/
#ifndef __CONFIG_H
/* #endif */
/* place code in last 4 MiB of RAM */
-#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
-#define CONFIG_SYS_TEXT_BASE 0x2fc00000
-#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
-#define CONFIG_SYS_TEXT_BASE 0x4fc00000
-#endif
#include "mx6_common.h"
-#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
+#if defined(CONFIG_TQMA6S)
#define PHYS_SDRAM_SIZE (512u * SZ_1M)
-#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
-#define PHYS_SDRAM_SIZE (1024u * SZ_1M)
+#elif defined(CONFIG_TQMA6DL)
+#define PHYS_SDRAM_SIZE (SZ_1G)
+#elif defined(CONFIG_TQMA6Q)
+#define PHYS_SDRAM_SIZE (SZ_1G)
#endif
#define CONFIG_MXC_UART
-/* SPI */
-#define CONFIG_MXC_SPI
-
/* SPI Flash */
#define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 100000
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75
-#define CONFIG_DTT_MAX_TEMP 70
-#define CONFIG_DTT_MIN_TEMP -30
-#define CONFIG_DTT_HYSTERESIS 3
-#define CONFIG_CMD_DTT
-
/* I2C EEPROM (M24C64) */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CONFIG_CMD_EEPROM
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_PHYLIB
#define CONFIG_MII
#define CONFIG_ARP_TIMEOUT 200UL
-/* Command definition */
-#define CONFIG_CMD_BMODE
-
#define CONFIG_ENV_SIZE (SZ_8K)
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M)
#if defined(CONFIG_TQMA6X_MMC_BOOT)
-#define CONFIG_ENV_IS_IN_MMC
#define TQMA6_UBOOT_OFFSET SZ_1K
#define TQMA6_UBOOT_SECTOR_START 0x2
#define TQMA6_UBOOT_SECTOR_COUNT 0x7fe
#define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \
TQMA6_UBOOT_SECTOR_COUNT)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET (TQMA6_UBOOT_SIZE)
#define CONFIG_ENV_SECT_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
"uboot=u-boot.imx\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \
- "console=" CONSOLE_DEV "\0" \
+ "console=" CONSOLE_DEV "\0" \
"cma_size="__stringify(TQMA6_CMA_SIZE)"\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"panicboot=echo No boot device !!! reset\0" \
TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
-#define CONFIG_STACKSIZE (128u * SZ_1K)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#endif
/* Support at least the sensor on TQMa6 SOM */
-#if !defined(CONFIG_DTT_SENSORS)
-#define CONFIG_DTT_SENSORS { 0 }
-#endif
#endif /* __CONFIG_H */