+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* ti_armv7_common.h
*
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
*
- * SPDX-License-Identifier: GPL-2.0+
- *
* The various ARMv7 SoCs from TI all share a number of IP blocks when
* implementing a given feature. Rather than define these in every
* board or even SoC common file, we define a common file to be re-used
#define DEFAULT_FIT_TI_ARGS \
"boot_fit=0\0" \
- "fit_loadaddr=0x87000000\0" \
- "fit_bootfile=fitImage\0" \
- "update_to_fit=setenv loadaddr ${fit_loadaddr}; setenv bootfile ${fit_bootfile}\0" \
- "loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \
+ "addr_fit=0x90000000\0" \
+ "name_fit=fitImage\0" \
+ "update_to_fit=setenv loadaddr ${addr_fit}; setenv bootfile ${name_fit}\0" \
+ "get_overlaystring=" \
+ "for overlay in $overlay_files;" \
+ "do;" \
+ "setenv overlaystring ${overlaystring}'#'${overlay};" \
+ "done;\0" \
+ "run_fit=bootm ${addr_fit}#${fdtfile}${overlaystring}\0" \
+ "loadfit=run args_mmc; run run_fit;\0" \
/*
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
* initial stack pointer in our SRAM. Otherwise, we can define
* CONFIG_NR_DRAM_BANKS before including this file.
*/
-#ifndef CONFIG_NR_DRAM_BANKS
-#define CONFIG_NR_DRAM_BANKS 1
-#endif
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#ifndef CONFIG_SYS_INIT_SP_ADDR
/* Timer information. */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-/*
- * Disable DM_* for SPL build and can be re-enabled after adding
- * DM support in SPL
- */
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_DM_I2C
-#endif
-
-/* I2C IP block */
+/* If DM_I2C, enable non-DM I2C support */
+#if !defined(CONFIG_DM_I2C)
#define CONFIG_I2C
-#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
-#else
-/*
- * Enable CONFIG_DM_I2C_COMPAT temporarily until all the i2c client
- * devices are adopted to DM
- */
-#define CONFIG_DM_I2C_COMPAT
#endif
-/* McSPI IP block */
-#define CONFIG_SPI
-
-/* GPIO block */
-
/*
* The following are general good-enough settings for U-Boot. We set a
* large malloc pool as we generally have a lot of DDR, and we opt for
* mtdparts, both for ease of use in U-Boot and for passing information
* on to the Linux kernel.
*/
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
-#define CONFIG_MTD_DEVICE /* Required for mtdparts */
-#endif
/*
* Our platforms make use of SPL to initalize the hardware (primarily
/* FAT sd card locations. */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#ifndef CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
#ifdef CONFIG_SPL_OS_BOOT
/* FAT */
/* General parts of the framework, required. */
-#ifdef CONFIG_NAND
+#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC