#define CONFIG_BOOTDELAY 1
/*
- * DDR information. We say (for simplicity) that we have 1 bank,
- * always, even when we have more. We always start at 0x80000000,
- * and we place the initial stack pointer in our SRAM.
+ * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
+ * we say (for simplicity) that we have 1 bank, always, even when
+ * we have more. We always start at 0x80000000, and we place the
+ * initial stack pointer in our SRAM. Otherwise, we can define
+ * CONFIG_NR_DRAM_BANKS before including this file.
*/
+#ifndef CONFIG_NR_DRAM_BANKS
#define CONFIG_NR_DRAM_BANKS 1
+#endif
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
/* Timer information. */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ 1000 /* 1ms clock */
/* I2C IP block */
#define CONFIG_I2C
#define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP24XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP24XX
/* MMC/SD IP block */
#define CONFIG_MMC
* access CS0 at is 0x8000000.
*/
#ifdef CONFIG_NAND
-#define CONFIG_CMD_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_BASE 0x8000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_CMD_NAND
#endif
/*
* console baudrate of 115200 and use the default baud rate table.
*/
#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
-#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "U-Boot# "
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */
+#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
+
+/* As stated above, the following choices are optional. */
+#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_PROMPT "U-Boot# "
#define CONFIG_VERSION_VARIABLE
-#define CONFIG_ENV_VARS_UBOOT_CONFIG
-#define CONFIG_BAUDRATE 115200
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 64
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
/*
* When we have SPI, NOR or NAND flash we expect to be making use of
* mtdparts, both for ease of use in U-Boot and for passing information
* useful commands. Note that we must have set CONFIG_SYS_NO_FLASH
* prior to this include, in order to skip a few commands. When we do
* have flash, if we expect these commands they must be enabled in that
- * config.
+ * config. If desired, a specific list of desired commands can be used
+ * instead.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
/* FAT */
#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
#endif
#ifdef CONFIG_MMC
+#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#endif
-/* General parts of the framework. */
+/* General parts of the framework, required. */
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS