#ifndef __CONFIG_TI_ARMV7_COMMON_H__
#define __CONFIG_TI_ARMV7_COMMON_H__
-/*
- * We typically do not contain NOR flash. In the cases where we do, we
- * undefine this later.
- */
-#define CONFIG_SYS_NO_FLASH
-
/* Support both device trees and ATAGs. */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
"ramdisk_addr_r=0x88080000\0" \
"scriptaddr=0x80000000\0" \
"pxefile_addr_r=0x80100000\0" \
- "bootm_size=0x10000000\0"
+ "bootm_size=0x10000000\0" \
+ "boot_fdt=try\0"
-#define DEFAULT_MMC_TI_ARGS \
- "mmcdev=0\0" \
- "mmcrootfstype=ext4 rootwait\0" \
- "finduuid=part uuid mmc ${bootpart} uuid\0" \
- "args_mmc=run finduuid;setenv bootargs console=${console} " \
- "${optargs} " \
- "root=PARTUUID=${uuid} rw " \
- "rootfstype=${mmcrootfstype}\0" \
- "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
- "source ${loadaddr}\0" \
- "bootenvfile=uEnv.txt\0" \
- "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
- "env import -t ${loadaddr} ${filesize}\0" \
- "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenvfile}\0" \
- "envboot=mmc dev ${mmcdev}; " \
- "if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootscript; then " \
- "run bootscript;" \
- "else " \
- "if run loadbootenv; then " \
- "echo Loaded env from ${bootenvfile};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "fi;" \
- "fi;\0" \
+#define DEFAULT_FIT_TI_ARGS \
+ "boot_fit=0\0" \
+ "fit_loadaddr=0x88000000\0" \
+ "fit_bootfile=fitImage\0" \
+ "update_to_fit=setenv loadaddr ${fit_loadaddr}; setenv bootfile ${fit_bootfile}\0" \
+ "loadfit=run args_mmc; bootm ${loadaddr}#${fdtfile};\0" \
/*
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
#define CONFIG_DM_I2C_COMPAT
#endif
-/* MMC/SD IP block */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-
/* McSPI IP block */
#define CONFIG_SPI
* we are on so we do not need to rely on the command prompt. We set a
* console baudrate of 115200 and use the default baud rate table.
*/
-#ifdef CONFIG_DFU_MMC
-#define CONFIG_SYS_MALLOC_LEN ((16 << 20) + CONFIG_SYS_DFU_DATA_BUF_SIZE)
-#else
-#define CONFIG_SYS_MALLOC_LEN (16 << 20)
-#endif
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_MALLOC_LEN SZ_32M
#define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */
#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
#define CONFIG_SYS_MAXARGS 64
/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 512
+#define CONFIG_SYS_CBSIZE 1024
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
* enabled a number of useful commands and support.
*/
#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
-#define CONFIG_DOS_PARTITION
#define CONFIG_FAT_WRITE
-#define CONFIG_PARTITION_UUIDS
-#define CONFIG_CMD_PART
#endif
/*
* Our platforms make use of SPL to initalize the hardware (primarily
- * memory) enough for full U-Boot to be loaded. We also support Falcon
- * Mode so that the Linux kernel can be booted directly from SPL
- * instead, if desired. We make use of the general SPL framework found
- * under common/spl/. Given our generally common memory map, we set a
- * number of related defaults and sizes here.
+ * memory) enough for full U-Boot to be loaded. We make use of the general
+ * SPL framework found under common/spl/. Given our generally common memory
+ * map, we set a number of related defaults and sizes here.
*/
#if !defined(CONFIG_NOR_BOOT) && \
!(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_OS_BOOT
+
+/*
+ * We also support Falcon Mode so that the Linux kernel can be booted
+ * directly from SPL. This is not currently available on HS devices.
+ */
/*
* Place the image at the start of the ROM defined image space (per
#ifndef CONFIG_SYS_SPL_MALLOC_START
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
CONFIG_SPL_BSS_MAX_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
+#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_8M
#endif
#ifndef CONFIG_SPL_MAX_SIZE
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
#endif
-/* RAW SD card / eMMC locations. */
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-
/* FAT sd card locations. */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_CMD_SPL
#endif
-#define CONFIG_SYS_THUMB_BUILD
-
/* General parts of the framework, required. */
-#define CONFIG_SPL_BOARD_INIT
#ifdef CONFIG_NAND
#define CONFIG_SPL_NAND_BASE
projects / platform / kernel / u-boot.git / blobdiff