#define CONFIG_SYS_TEXT_BASE 0x80008000
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#define CONFIG_OMAP3_GPIO_5
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_ULPI
-#define CONFIG_USB_ULPI_VIEWPORT_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_STORAGE
/* commands to include */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC /* MMC support */
#define CONFIG_CMD_NAND /* NAND support */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_NO_FLASH
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
#define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+
+/* FAT */
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
+
/* NAND boot config */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
-#define CONFIG_OF_LIBFDT
-#define CONFIG_FIT
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
"fi;" \
"else echo U-Boot not downloaded..exiting;fi\0" \
-
/*
* this is common code for all TAM3517 boards.
* MAC address is stored from manufacturer in
if (i) \
sprintf(ethname, "eth%daddr", i); \
else \
- sprintf(ethname, "ethaddr"); \
+ strcpy(ethname, "ethaddr"); \
printf("Setting %s from EEPROM with %s\n", ethname, buf);\
setenv(ethname, buf); \
} \