#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME taishan
+#define CONFIG_USE_TTY ttyS1
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */
-#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*-----------------------------------------------------------------------
* E2PROM bootstrap configure value
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#undef CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR 0x50
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=taishan\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/taishan/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \
"kozio=bootm 0xffe00000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*-----------------------------------------------------------------------
* Networking
*----------------------------------------------------------------------*/
#define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */
#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */
#define CONFIG_PHY2_ADDR 0x1
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff