#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
#endif
#define CONFIG_CMD_REGINFO
/* High Level Configuration Options */
#define CONFIG_BOOKE
-#define CONFIG_E6500
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
#define CONFIG_SRIO2 /* SRIO port 2 */
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
#define CONFIG_FSL_LAW /* Use common FSL init code */
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \
- FTIM0_NOR_TEADC(0x01) | \
- FTIM0_NOR_TEAHC(0x20))
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1A) |\
FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \
- FTIM2_NOR_TCH(0x0E) | \
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWPH(0x0E) | \
FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3 0x0
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
-/* VSC Crossbar switches */
-#define CONFIG_VSC_CROSSBAR
#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_VOL_MONITOR 0xa
#define I2C_MUX_CH_VSC3316_FS 0xc
#define I2C_MUX_CH_VSC3316_BS 0xd
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+
+/* VSC Crossbar switches */
+#define CONFIG_VSC_CROSSBAR
#define VSC3316_FSM_TX_ADDR 0x70
#define VSC3316_FSM_RX_ADDR 0x71
*/
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_SST
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
-#define XFI_CARD_PORT1_PHY_ADDR 0x1 /* tmp, FIXME below addr */
-#define XFI_CARD_PORT2_PHY_ADDR 0x2
-#define XFI_CARD_PORT3_PHY_ADDR 0x3
-#define XFI_CARD_PORT4_PHY_ADDR 0x4
-#define QSGMII_CARD_PHY_ADDR 0x5
-#define FM1_10GEC1_PHY_ADDR 0x6
-#define FM1_10GEC2_PHY_ADDR 0x7
-#define FM2_10GEC1_PHY_ADDR 0x8
-#define FM2_10GEC2_PHY_ADDR 0x9
+#define FM1_10GEC1_PHY_ADDR 0x0
+#define FM1_10GEC2_PHY_ADDR 0x1
+#define FM2_10GEC1_PHY_ADDR 0x2
+#define FM2_10GEC2_PHY_ADDR 0x3
#endif
#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_E1000
#define __USB_PHY_TYPE utmi
+/*
+ * T4240 has 3 DDR controllers. Default to 3way_4KB interleaving. It can be
+ * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to
+ * cacheline interleaving. It can be cacheline, page, bank, superbank.
+ * See doc/README.fsl-ddr for details.
+ */
+#ifdef CONFIG_PPC_T4240
+#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
+
#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=3way_4KB," \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
"bank_intlv=auto;" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \