#ifndef _SUNXI_COMMON_CONFIG_H
#define _SUNXI_COMMON_CONFIG_H
+#include <asm/arch/cpu.h>
+#include <linux/stringify.h>
+
#ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT
/*
* The U-Boot workarounds bugs in the outdated buggy sunxi-3.4 kernels at the
#define CONFIG_SYS_THUMB_BUILD /* Thumbs mode to save space in SPL */
#endif
-#include <asm/arch/cpu.h> /* get chip and board defs */
-
-#define CONFIG_SYS_TEXT_BASE 0x4a000000
-
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_DM)
-# define CONFIG_DW_SERIAL
-#endif
-
-/*
- * Display CPU information
- */
-#define CONFIG_DISPLAY_CPUINFO
-
-#define CONFIG_SYS_PROMPT "sunxi# "
-
/* Serial & console */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
/* ns16550 reg in the low bits of cpu reg */
#define CONFIG_SYS_NS16550_CLK 24000000
-#ifndef CONFIG_DM_SERIAL
+#ifdef CONFIG_DM_SERIAL
+# define CONFIG_DW_SERIAL
+#else
# define CONFIG_SYS_NS16550_REG_SIZE -4
# define CONFIG_SYS_NS16550_COM1 SUNXI_UART0_BASE
# define CONFIG_SYS_NS16550_COM2 SUNXI_UART1_BASE
# define CONFIG_SYS_NS16550_COM5 SUNXI_R_UART_BASE
#endif
-/* DRAM Base */
+/* CPU */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+/*
+ * The DRAM Base differs between some models. We cannot use macros for the
+ * CONFIG_FOO defines which contain the DRAM base address since they end
+ * up unexpanded in include/autoconf.mk .
+ *
+ * So we have to have this #ifdef #else #endif block for these.
+ */
+#ifdef CONFIG_MACH_SUN9I
+#define SDRAM_OFFSET(x) 0x2##x
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* default load address */
+#define CONFIG_SYS_TEXT_BASE 0x2a000000
+#define CONFIG_PRE_CON_BUF_ADDR 0x2f000000
+/* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
+ * since it needs to fit in with the other values. By also #defining it
+ * we get warnings if the Kconfig value mismatches. */
+#define CONFIG_SPL_STACK_R_ADDR 0x2fe00000
+#define CONFIG_SPL_BSS_START_ADDR 0x2ff80000
+#else
+#define SDRAM_OFFSET(x) 0x4##x
#define CONFIG_SYS_SDRAM_BASE 0x40000000
+#define CONFIG_SYS_LOAD_ADDR 0x42000000 /* default load address */
+#define CONFIG_SYS_TEXT_BASE 0x4a000000
+#define CONFIG_PRE_CON_BUF_ADDR 0x4f000000
+/* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
+ * since it needs to fit in with the other values. By also #defining it
+ * we get warnings if the Kconfig value mismatches. */
+#define CONFIG_SPL_STACK_R_ADDR 0x4fe00000
+#define CONFIG_SPL_BSS_START_ADDR 0x4ff80000
+#endif
+
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000 /* 512 KiB */
+
+#ifdef CONFIG_MACH_SUN9I
+/*
+ * The A80's A1 sram starts at 0x00010000 rather then at 0x00000000 and is
+ * slightly bigger. Note that it is possible to map the first 32 KiB of the
+ * A1 at 0x00000000 like with older SoCs by writing 0x16aa0001 to the
+ * undocumented 0x008000e0 SYS_CTRL register. Where the 16aa is a key and
+ * the 1 actually activates the mapping of the first 32 KiB to 0x00000000.
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR 0x10000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x0a000 /* 40 KiB */
+#else
#define CONFIG_SYS_INIT_RAM_ADDR 0x0
#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* 32 KiB */
+#endif
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SUNXI_AHCI
+#define CONFIG_SYS_64BIT_LBA
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
#define CONFIG_CMD_SCSI
#endif
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_SETEXPR
-
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_CMDLINE_TAG
#define CONFIG_INITRD_TAG
+#define CONFIG_SERIAL_TAG
+
+#ifdef CONFIG_NAND_SUNXI
+#define CONFIG_SPL_NAND_SUPPORT 1
+#endif
/* mmc config */
-#if !defined(CONFIG_UART0_PORT_F)
-#define CONFIG_MMC
+#ifdef CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_CMD_MMC
#define CONFIG_MMC_SUNXI
#define CONFIG_SYS_MMC_ENV_DEV 0 /* first detected MMC controller */
#endif
-/* 4MB of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
+/* 64MB of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (64 << 20))
/*
* Miscellaneous configurable options
*/
-#define CONFIG_CMD_ECHO
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_LOAD_ADDR 0x42000000 /* default load address */
-
/* standalone support */
-#define CONFIG_STANDALONE_LOAD_ADDR 0x42000000
+#define CONFIG_STANDALONE_LOAD_ADDR CONFIG_SYS_LOAD_ADDR
/* baudrate */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* 512 KiB */
+#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* 768 KiB */
#define CONFIG_IDENT_STRING " Allwinner Technology"
#define CONFIG_ENV_OFFSET (544 << 10) /* (8 + 24 + 512) KiB */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-
#define CONFIG_FAT_WRITE /* enable write access */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_LOAD_IMAGE
-#ifdef CONFIG_SPL_FEL
-
-#define CONFIG_SPL_TEXT_BASE 0x2000
-#define CONFIG_SPL_MAX_SIZE 0x4000 /* 16 KiB */
-
-#else /* CONFIG_SPL */
-
-#define CONFIG_SPL_BSS_START_ADDR 0x4ff80000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KiB */
-
#define CONFIG_SPL_TEXT_BASE 0x20 /* sram start+header */
#define CONFIG_SPL_MAX_SIZE 0x5fe0 /* 24KB on sun4i/sun7i */
#define CONFIG_SPL_LIBDISK_SUPPORT
-#if !defined(CONFIG_UART0_PORT_F)
+#ifdef CONFIG_MMC
#define CONFIG_SPL_MMC_SUPPORT
#endif
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 80 /* 40KiB */
#define CONFIG_SPL_PAD_TO 32768 /* decimal for 'dd' */
-#endif /* CONFIG_SPL */
-
/* end of 32 KiB in sram */
#define LOW_LEVEL_SRAM_STACK 0x00008000 /* End of sram */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
-#define CONFIG_SYS_SPL_MALLOC_START 0x4ff00000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000 /* 512 KiB */
/* I2C */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER
#define CONFIG_CONS_INDEX 1 /* UART0 */
#endif
+#ifdef CONFIG_REQUIRE_SERIAL_CONSOLE
#if CONFIG_CONS_INDEX == 1
#ifdef CONFIG_MACH_SUN9I
#define OF_STDOUT_PATH "/soc/serial@07000000:115200"
#endif
#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I)
#define OF_STDOUT_PATH "/soc@01c00000/serial@01c28400:115200"
+#elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I)
+#define OF_STDOUT_PATH "/soc@01c00000/serial@01c28800:115200"
#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I)
#define OF_STDOUT_PATH "/soc@01c00000/serial@01f02800:115200"
#else
#error Unsupported console port nr. Please fix stdout-path in sunxi-common.h.
#endif
+#endif /* ifdef CONFIG_REQUIRE_SERIAL_CONSOLE */
/* GPIO */
#define CONFIG_SUNXI_GPIO
* The amount of RAM to keep free at the top of RAM when relocating u-boot,
* to use as framebuffer. This must be a multiple of 4096.
*/
-#define CONFIG_SUNXI_MAX_FB_SIZE (9 << 20)
+#define CONFIG_SUNXI_MAX_FB_SIZE (16 << 20)
/* Do we want to initialize a simple FB? */
#define CONFIG_VIDEO_DT_SIMPLEFB
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_STD_TIMINGS
#define CONFIG_I2C_EDID
+#define VIDEO_LINE_LEN (pGD->plnSizeX)
/* allow both serial and cfb console. */
#define CONFIG_CONSOLE_MUX
#define CONFIG_PHYLIB
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_OHCI_SUNXI
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
#endif
#ifdef CONFIG_USB_MUSB_SUNXI
-#define CONFIG_MUSB_HOST
-#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_USB_MUSB_PIO_ONLY
+#endif
+
+#ifdef CONFIG_USB_MUSB_GADGET
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 0
+
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_USB_FUNCTION_FASTBOOT
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#endif
+
+#ifdef CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_G_DNL_VENDOR_NUM 0x1f3a
+#define CONFIG_G_DNL_PRODUCT_NUM 0x1010
+#define CONFIG_G_DNL_MANUFACTURER "Allwinner Technology"
+#endif
+
+#ifdef CONFIG_USB_FUNCTION_FASTBOOT
+#define CONFIG_CMD_FASTBOOT
+#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
+#define CONFIG_FASTBOOT_BUF_SIZE 0x2000000
+#define CONFIG_ANDROID_BOOT_IMAGE
+
+#define CONFIG_FASTBOOT_FLASH
+
+#ifdef CONFIG_MMC
+#define CONFIG_FASTBOOT_FLASH_MMC_DEV 0
+#define CONFIG_EFI_PARTITION
+#endif
#endif
-#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_SUNXI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
+#ifdef CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_CMD_USB_MASS_STORAGE
#endif
#ifdef CONFIG_USB_KEYBOARD
/* Enable pre-console buffer to get complete log on the VGA console */
#define CONFIG_PRE_CONSOLE_BUFFER
-#define CONFIG_PRE_CON_BUF_SZ (1024 * 1024)
-/* Use the room between the end of bootm_size and the framebuffer */
-#define CONFIG_PRE_CON_BUF_ADDR 0x4f000000
+#define CONFIG_PRE_CON_BUF_SZ 4096 /* Aprox 2 80*25 screens */
/*
- * 240M RAM (256M minimum minus space for the framebuffer),
+ * 160M RAM (256M minimum minus 64MB heap + 32MB for u-boot, stack, fb, etc.
* 32M uncompressed kernel, 16M compressed kernel, 1M fdt,
* 1M script, 1M pxe and the ramdisk at the end.
*/
#define MEM_LAYOUT_ENV_SETTINGS \
- "bootm_size=0xf000000\0" \
- "kernel_addr_r=0x42000000\0" \
- "fdt_addr_r=0x43000000\0" \
- "scriptaddr=0x43100000\0" \
- "pxefile_addr_r=0x43200000\0" \
- "ramdisk_addr_r=0x43300000\0"
+ "bootm_size=0xa000000\0" \
+ "kernel_addr_r=" __stringify(SDRAM_OFFSET(2000000)) "\0" \
+ "fdt_addr_r=" __stringify(SDRAM_OFFSET(3000000)) "\0" \
+ "scriptaddr=" __stringify(SDRAM_OFFSET(3100000)) "\0" \
+ "pxefile_addr_r=" __stringify(SDRAM_OFFSET(3200000)) "\0" \
+ "ramdisk_addr_r=" __stringify(SDRAM_OFFSET(3300000)) "\0"
#ifdef CONFIG_MMC
#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
#define BOOT_TARGET_DEVICES_SCSI(func)
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_STORAGE
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_DEVICES_USB(func)
#endif
+/* FEL boot support, auto-execute boot.scr if a script address was provided */
+#define BOOTENV_DEV_FEL(devtypeu, devtypel, instance) \
+ "bootcmd_fel=" \
+ "if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then " \
+ "echo '(FEL boot)'; " \
+ "source ${fel_scriptaddr}; " \
+ "fi\0"
+#define BOOTENV_DEV_NAME_FEL(devtypeu, devtypel, instance) \
+ "fel "
+
#define BOOT_TARGET_DEVICES(func) \
+ func(FEL, fel, na) \
BOOT_TARGET_DEVICES_MMC(func) \
BOOT_TARGET_DEVICES_SCSI(func) \
BOOT_TARGET_DEVICES_USB(func) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
+#ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT
+#define BOOTCMD_SUNXI_COMPAT \
+ "bootcmd_sunxi_compat=" \
+ "setenv root /dev/mmcblk0p3 rootwait; " \
+ "if ext2load mmc 0 0x44000000 uEnv.txt; then " \
+ "echo Loaded environment from uEnv.txt; " \
+ "env import -t 0x44000000 ${filesize}; " \
+ "fi; " \
+ "setenv bootargs console=${console} root=${root} ${extraargs}; " \
+ "ext2load mmc 0 0x43000000 script.bin && " \
+ "ext2load mmc 0 0x48000000 uImage && " \
+ "bootm 0x48000000\0"
+#else
+#define BOOTCMD_SUNXI_COMPAT
+#endif
+
#include <config_distro_bootcmd.h>
#ifdef CONFIG_USB_KEYBOARD
MEM_LAYOUT_ENV_SETTINGS \
"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"console=ttyS0,115200\0" \
+ BOOTCMD_SUNXI_COMPAT \
BOOTENV
#else /* ifndef CONFIG_SPL_BUILD */