#define CONFIG_TSEC_ENET /* tsec ethernet support*/
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CFG_OR0_PRELIM (CFG_FLASH_BASE | 0x0FF7)
#define CFG_FLASH_CFI 1
-#define CFG_FLASH_CFI_DRIVER 1
+#define CONFIG_FLASH_CFI_DRIVER 1
#undef CFG_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#undef CONFIG_FSL_DDR_INTERACTIVE
-/*
- * DDR Setup
- */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */
#undef CONFIG_CLOCKS_IN_MHZ
#define CFG_I2C_EEPROM_ADDR 0x51 /* 1010001x */
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
/*
/* Environment - default config is in flash, see below */
#if 0 /* in EEPROM */
-# define CFG_ENV_IS_IN_EEPROM 1
-# define CFG_ENV_OFFSET 0
-# define CFG_ENV_SIZE 2048
+# define CONFIG_ENV_IS_IN_EEPROM 1
+# define CONFIG_ENV_OFFSET 0
+# define CONFIG_ENV_SIZE 2048
#else /* in flash */
-# define CFG_ENV_IS_IN_FLASH 1
+# define CONFIG_ENV_IS_IN_FLASH 1
# ifdef CONFIG_STXSSA_4M
-# define CFG_ENV_SECT_SIZE 0x20000
+# define CONFIG_ENV_SECT_SIZE 0x20000
# else /* default configuration - 64 MiB flash */
-# define CFG_ENV_SECT_SIZE 0x40000
+# define CONFIG_ENV_SECT_SIZE 0x40000
# endif
-# define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
-# define CFG_ENV_SIZE 0x4000
-# define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
-# define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+# define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+# define CONFIG_ENV_SIZE 0x4000
+# define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+# define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
* but only little space is available, so we use a very simple setup.
* With environment in flash, we use a more powerful default configuration.
*/
-#ifdef CFG_ENV_IS_IN_EEPROM /* use restricted "standard" environment */
+#ifdef CONFIG_ENV_IS_IN_EEPROM /* use restricted "standard" environment */
#define CONFIG_BAUDRATE 38400
""
#define CONFIG_BOOTCOMMAND "run flash_self"
-#endif /* CFG_ENV_IS_IN_EEPROM */
+#endif /* CONFIG_ENV_IS_IN_EEPROM */
#endif /* __CONFIG_H */