#include <linux/sizes.h>
#include <asm/arch/stm32.h>
-/*
- * Number of clock ticks in 1 sec
- */
-#define CONFIG_SYS_HZ 1000
-
-#ifndef CONFIG_STM32MP1_TRUSTED
+#ifndef CONFIG_TFABOOT
/* PSCI support */
-#define CONFIG_ARMV7_PSCI_1_0
#define CONFIG_ARMV7_SECURE_BASE STM32_SYSRAM_BASE
#define CONFIG_ARMV7_SECURE_MAX_SIZE STM32_SYSRAM_SIZE
#endif
#define CONFIG_SYS_CBSIZE SZ_1K
/*
- * Needed by "loadb"
+ * default load address used for command tftp, bootm , loadb, ...
*/
-#define CONFIG_SYS_LOAD_ADDR STM32_DDR_BASE
+#define CONFIG_SYS_LOAD_ADDR 0xc2000000
/* ATAGs */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ SZ_256M
+
/* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN SZ_32M
+#define CONFIG_SYS_BOOTM_LEN SZ_32M
/* SPL support */
#ifdef CONFIG_SPL
-/* BOOTROM load address */
/* SPL use DDR */
-#define CONFIG_SPL_BSS_START_ADDR 0xC0200000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0xC0300000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x01D00000
-/* limit SYSRAM usage to first 128 KB */
-#define CONFIG_SPL_MAX_SIZE 0x00020000
+/* Restrict SPL to fit within SYSRAM */
+#define STM32_SYSRAM_END (STM32_SYSRAM_BASE + STM32_SYSRAM_SIZE)
+#define CONFIG_SPL_MAX_FOOTPRINT (STM32_SYSRAM_END - CONFIG_SPL_TEXT_BASE)
#define CONFIG_SPL_STACK (STM32_SYSRAM_BASE + \
STM32_SYSRAM_SIZE)
#endif /* #ifdef CONFIG_SPL */
-
-#define CONFIG_SYS_MEMTEST_START STM32_DDR_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_64M)
-#define CONFIG_SYS_MEMTEST_SCRATCH (CONFIG_SYS_MEMTEST_END + 4)
-
/*MMC SD*/
#define CONFIG_SYS_MMC_MAX_DEVICE 3
+/* NAND support */
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+/* Ethernet need */
+#ifdef CONFIG_DWC_ETH_QOS
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_BOOTP_SERVERIP
+#define CONFIG_SYS_AUTOLOAD "no"
+#endif
+
/*****************************************************************************/
#ifdef CONFIG_DISTRO_DEFAULTS
/*****************************************************************************/
#if !defined(CONFIG_SPL_BUILD)
-/* NAND support */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 1) \
- func(MMC, mmc, 0) \
- func(MMC, mmc, 2)
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
+#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
+#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
+#else
+#define BOOT_TARGET_MMC0(func)
+#define BOOT_TARGET_MMC1(func)
+#define BOOT_TARGET_MMC2(func)
+#endif
+
+#ifdef CONFIG_NET
+#define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
+#else
+#define BOOT_TARGET_PXE(func)
+#endif
+
+#ifdef CONFIG_CMD_UBIFS
+#define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0)
+#else
+#define BOOT_TARGET_UBIFS(func)
+#endif
+
+#ifdef CONFIG_CMD_USB
+#define BOOT_TARGET_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_USB(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_MMC1(func) \
+ BOOT_TARGET_UBIFS(func) \
+ BOOT_TARGET_MMC0(func) \
+ BOOT_TARGET_MMC2(func) \
+ BOOT_TARGET_USB(func) \
+ BOOT_TARGET_PXE(func)
+
/*
* bootcmd for stm32mp1:
* for serial/usb: execute the stm32prog command
* for mmc boot (eMMC, SD card), boot only on the same device
- * for nand boot, boot with on ubifs partition on nand
- * for nor boot, use the default order
+ * for nand or spi-nand boot, boot with on ubifs partition on UBI partition
+ * for nor boot, use SD card = mmc0
*/
#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
"echo \"Boot over ${boot_device}${boot_instance}!\";" \
"if test ${boot_device} = serial || test ${boot_device} = usb;" \
"then stm32prog ${boot_device} ${boot_instance}; " \
"else " \
+ "run env_check;" \
"if test ${boot_device} = mmc;" \
"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
- "if test ${boot_device} = nand;" \
+ "if test ${boot_device} = nand ||" \
+ " test ${boot_device} = spi-nand ;" \
"then env set boot_targets ubifs0; fi;" \
+ "if test ${boot_device} = nor;" \
+ "then env set boot_targets mmc0; fi;" \
"run distro_bootcmd;" \
"fi;\0"
+#ifdef CONFIG_FASTBOOT_CMD_OEM_FORMAT
+/* eMMC default partitions for fastboot command: oem format */
+#define PARTS_DEFAULT \
+ "partitions=" \
+ "name=ssbl,size=2M;" \
+ "name=bootfs,size=64MB,bootable;" \
+ "name=vendorfs,size=16M;" \
+ "name=rootfs,size=746M;" \
+ "name=userfs,size=-\0"
+#else
+#define PARTS_DEFAULT
+#endif
+
#include <config_distro_bootcmd.h>
/*
* memory layout for 32M uncompressed/compressed kernel,
- * 1M fdt, 1M script, 1M pxe and 1M for splashimage
+ * 1M fdt, 1M script, 1M pxe and 1M for overlay
* and the ramdisk at the end.
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdt_addr_r=0xc4000000\0" \
"scriptaddr=0xc4100000\0" \
"pxefile_addr_r=0xc4200000\0" \
- "splashimage=0xc4300000\0" \
+ "fdtoverlay_addr_r=0xc4300000\0" \
"ramdisk_addr_r=0xc4400000\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
+ "altbootcmd=run bootcmd\0" \
+ "env_check=if env info -p -d -q; then env save; fi\0" \
STM32MP_BOOTCMD \
- BOOTENV
+ PARTS_DEFAULT \
+ BOOTENV \
+ "boot_net_usb_start=true\0"
#endif /* ifndef CONFIG_SPL_BUILD */
#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
projects / platform / kernel / u-boot.git / blobdiff