#include <linux/sizes.h>
#include <asm/arch/stm32.h>
-#define CONFIG_PREBOOT
-
-/*
- * Number of clock ticks in 1 sec
- */
-#define CONFIG_SYS_HZ 1000
-
+#ifndef CONFIG_TFABOOT
/* PSCI support */
#define CONFIG_ARMV7_PSCI_1_0
#define CONFIG_ARMV7_SECURE_BASE STM32_SYSRAM_BASE
#define CONFIG_ARMV7_SECURE_MAX_SIZE STM32_SYSRAM_SIZE
-
-/*
- * malloc() pool size
- */
-#define CONFIG_SYS_MALLOC_LEN SZ_32M
+#endif
/*
* Configuration of the external SRAM memory used by U-Boot
#define CONFIG_SYS_SDRAM_BASE STM32_DDR_BASE
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
-#define CONFIG_NR_DRAM_BANKS 1
+#ifdef CONFIG_STM32MP1_OPTEE
+#define CONFIG_SYS_MEM_TOP_HIDE SZ_32M
+#endif /* CONFIG_STM32MP1_OPTEE */
/*
* Console I/O buffer size
#define CONFIG_SYS_CBSIZE SZ_1K
/*
- * Needed by "loadb"
- */
-#define CONFIG_SYS_LOAD_ADDR STM32_DDR_BASE
-
-/*
- * Env parameters
+ * default load address used for command tftp, bootm , loadb, ...
*/
-#define CONFIG_ENV_SIZE SZ_4K
+#define CONFIG_LOADADDR 0xc2000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* ATAGs */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ SZ_256M
+
+/* Extend size of kernel image for uncompression */
+#define CONFIG_SYS_BOOTM_LEN SZ_32M
+
/* SPL support */
#ifdef CONFIG_SPL
-/* BOOTROM load address */
-#define CONFIG_SPL_TEXT_BASE 0x2FFC2500
/* SPL use DDR */
#define CONFIG_SPL_BSS_START_ADDR 0xC0200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
STM32_SYSRAM_SIZE)
#endif /* #ifdef CONFIG_SPL */
+#define CONFIG_SYS_MEMTEST_START STM32_DDR_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_64M)
+#define CONFIG_SYS_MEMTEST_SCRATCH (CONFIG_SYS_MEMTEST_END + 4)
+
/*MMC SD*/
#define CONFIG_SYS_MMC_MAX_DEVICE 3
-#define CONFIG_SUPPORT_EMMC_BOOT
-#if !defined(CONFIG_SPL) || !defined(CONFIG_SPL_BUILD)
+/* NAND support */
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+/* Ethernet need */
+#ifdef CONFIG_DWC_ETH_QOS
+#define CONFIG_SYS_NONCACHED_MEMORY (1 * SZ_1M) /* 1M */
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_BOOTP_SERVERIP
+#define CONFIG_SYS_AUTOLOAD "no"
+#endif
+
+/* Dynamic MTD partition support */
+#if defined(CONFIG_STM32_QSPI) || defined(CONFIG_NAND_STM32_FMC2)
+#define CONFIG_SYS_MTDPARTS_RUNTIME
+#endif
+
+#define CONFIG_SET_DFU_ALT_INFO
+
+#ifdef CONFIG_DM_VIDEO
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_BMP_16BPP
+#define CONFIG_BMP_24BPP
+#define CONFIG_BMP_32BPP
+#endif
+
+/*****************************************************************************/
+#ifdef CONFIG_DISTRO_DEFAULTS
+/*****************************************************************************/
+
+#if !defined(CONFIG_SPL_BUILD)
+
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
+#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
+#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
+#else
+#define BOOT_TARGET_MMC0(func)
+#define BOOT_TARGET_MMC1(func)
+#define BOOT_TARGET_MMC2(func)
+#endif
+
+#ifdef CONFIG_NET
+#define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
+#else
+#define BOOT_TARGET_PXE(func)
+#endif
+
+#ifdef CONFIG_CMD_UBIFS
+#define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0)
+#else
+#define BOOT_TARGET_UBIFS(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_MMC1(func) \
+ BOOT_TARGET_UBIFS(func) \
+ BOOT_TARGET_MMC0(func) \
+ BOOT_TARGET_MMC2(func) \
+ BOOT_TARGET_PXE(func)
-#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 1) \
- func(MMC, mmc, 0) \
- func(MMC, mmc, 2)
+/*
+ * bootcmd for stm32mp1:
+ * for serial/usb: execute the stm32prog command
+ * for mmc boot (eMMC, SD card), boot only on the same device
+ * for nand boot, boot with on ubifs partition on nand
+ * for nor boot, use the default order
+ */
+#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
+ "echo \"Boot over ${boot_device}${boot_instance}!\";" \
+ "if test ${boot_device} = serial || test ${boot_device} = usb;" \
+ "then stm32prog ${boot_device} ${boot_instance}; " \
+ "else " \
+ "run env_check;" \
+ "if test ${boot_device} = mmc;" \
+ "then env set boot_targets \"mmc${boot_instance}\"; fi;" \
+ "if test ${boot_device} = nand;" \
+ "then env set boot_targets ubifs0; fi;" \
+ "run distro_bootcmd;" \
+ "fi;\0"
#include <config_distro_bootcmd.h>
-#define STM32MP_PREBOOT \
- "echo \"Boot over ${boot_device}${boot_instance}!\"; " \
- "if test \"${boot_device}\" = \"mmc\"; then " \
- "env set boot_targets \"mmc${boot_instance}\"; "\
- "fi;"
+#ifdef CONFIG_STM32MP1_OPTEE
+/* with OPTEE: define specific MTD partitions = teeh, teed, teex */
+#define STM32MP_MTDPARTS \
+ "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),256k(teeh),256k(teed),256k(teex),-(nor_user)\0" \
+ "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),512k(teeh),512k(teed),512k(teex),-(UBI)\0" \
+ "mtdparts_spi-nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),"\
+ "512k(teeh),512k(teed),512k(teex),-(UBI)\0"
+
+#else /* CONFIG_STM32MP1_OPTEE */
+#define STM32MP_MTDPARTS \
+ "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),-(nor_user)\0" \
+ "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0" \
+ "mtdparts_spi-nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0"
+
+#endif /* CONFIG_STM32MP1_OPTEE */
+
+#ifndef CONFIG_SYS_MTDPARTS_RUNTIME
+#undef STM32MP_MTDPARTS
+#define STM32MP_MTDPARTS
+#endif
+
+#define STM32MP_DFU_ALT_RAM \
+ "dfu_alt_info_ram=ram 0=" \
+ "uImage ram ${kernel_addr_r} 0x2000000;" \
+ "devicetree.dtb ram ${fdt_addr_r} 0x100000;" \
+ "uramdisk.image.gz ram ${ramdisk_addr_r} 0x10000000\0"
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define STM32MP_DFU_ALT_INFO \
+ "dfu_alt_info_nor0=mtd nor0=" \
+ "nor_fsbl1 part 1;nor_fsbl2 part 2;" \
+ "nor_ssbl part 3;nor_env part 4\0" \
+ "dfu_alt_info_nand0=mtd nand0="\
+ "nand_fsbl part 1;nand_ssbl1 part 2;" \
+ "nand_ssbl2 part 3;nand_UBI partubi 4\0" \
+ "dfu_alt_info_spi-nand0=mtd spi-nand0="\
+ "spi-nand_fsbl part 1;spi-nand_ssbl1 part 2;" \
+ "spi-nand_ssbl2 part 3;spi-nand_UBI partubi 4\0" \
+ "dfu_alt_info_mmc0=mmc 0=" \
+ "sdcard_fsbl1 part 0 1;sdcard_fsbl2 part 0 2;" \
+ "sdcard_ssbl part 0 3;sdcard_bootfs part 0 4;" \
+ "sdcard_vendorfs part 0 5;sdcard_rootfs part 0 6;" \
+ "sdcard_userfs part 0 7\0" \
+ "dfu_alt_info_mmc1=mmc 1=" \
+ "emmc_fsbl1 raw 0x0 0x200 mmcpart 1;" \
+ "emmc_fsbl2 raw 0x0 0x200 mmcpart 2;emmc_ssbl part 1 1;" \
+ "emmc_bootfs part 1 2;emmc_vendorfs part 1 3;" \
+ "emmc_rootfs part 1 4;emmc_userfs part 1 5\0"
+#else
+#define STM32MP_DFU_ALT_INFO
+#endif
+/*
+ * memory layout for 32M uncompressed/compressed kernel,
+ * 1M fdt, 1M script, 1M pxe and 1M for splashimage
+ * and the ramdisk at the end.
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "scriptaddr=0xC0000000\0" \
- "pxefile_addr_r=0xC0000000\0" \
- "kernel_addr_r=0xC1000000\0" \
- "fdt_addr_r=0xC4000000\0" \
- "ramdisk_addr_r=0xC4100000\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "preboot=" STM32MP_PREBOOT "\0" \
- BOOTENV
+ "bootdelay=1\0" \
+ "kernel_addr_r=0xc2000000\0" \
+ "fdt_addr_r=0xc4000000\0" \
+ "scriptaddr=0xc4100000\0" \
+ "pxefile_addr_r=0xc4200000\0" \
+ "splashimage=0xc4300000\0" \
+ "ramdisk_addr_r=0xc4400000\0" \
+ "altbootcmd=run bootcmd\0" \
+ "env_default=1\0" \
+ "env_check=if test $env_default -eq 1;"\
+ " then env set env_default 0;env save;fi\0" \
+ STM32MP_BOOTCMD \
+ STM32MP_MTDPARTS \
+ STM32MP_DFU_ALT_RAM \
+ STM32MP_DFU_ALT_INFO \
+ BOOTENV \
+ "boot_net_usb_start=true\0"
#endif /* ifndef CONFIG_SPL_BUILD */
+#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff