#define CONFIG_MPC8220 1
#define CONFIG_SORCERY 1 /* Sorcery board */
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* Input clock running at 60Mhz, read Hid1 for the CPU multiplier to
determine the CPU speed. */
#define CFG_MPC8220_CLKIN 60000000 /* ... running at 60MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC8220 CPUs */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Serial console configuration
*/
#define CONFIG_PCI_CFG_PHYS CONFIG_PCI_CFG_BUS
#define CONFIG_PCI_CFG_SIZE 0x01000000
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_BOOTD | \
- CFG_CMD_CACHE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_SNTP | \
- 0)
-
-/* CFG_CMD_MII | \ */
-/* CFG_CMD_USB | \ */
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+
/*
* Default Environment
#define CONFIG_HOSTNAME sorcery
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */
#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, \
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, \
CFG_FLASH_BASE+0x04000000 } /* two banks */
/*
/* SDRAM configuration (for SPD) */
#define CFG_SDRAM_TOTAL_BANKS 1
-#define CFG_SDRAM_SPD_I2C_ADDR 0x50 /* 7bit */
+#define CFG_SDRAM_SPD_I2C_ADDR 0x50 /* 7bit */
#define CFG_SDRAM_SPD_SIZE 0x100
-#define CFG_SDRAM_CAS_LATENCY 5 /* (CL=2.5)x2 */
+#define CFG_SDRAM_CAS_LATENCY 5 /* (CL=2.5)x2 */
/* SDRAM drive strength register (for SSTL_2 class II)*/
-#define CFG_SDRAM_DRIVE_STRENGTH ((DRIVE_STRENGTH_HIGH << SDRAMDS_SBE_SHIFT) | \
+#define CFG_SDRAM_DRIVE_STRENGTH ((DRIVE_STRENGTH_HIGH << SDRAMDS_SBE_SHIFT) | \
(DRIVE_STRENGTH_HIGH << SDRAMDS_SBC_SHIFT) | \
(DRIVE_STRENGTH_HIGH << SDRAMDS_SBA_SHIFT) | \
(DRIVE_STRENGTH_HIGH << SDRAMDS_SBS_SHIFT) | \
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8220 CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/