#ifndef __CONFIG_H
#define __CONFIG_H
+/* new uImage format support */
+#define CONFIG_FIT 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
+#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00000000
-#define CFG_MEMTEST_END 0x10000000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00400000
+#define CONFIG_SYS_MEMTEST_END 0x00C00000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
-#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
/* Hardcoded values, to use instead of SPD */
-#define CFG_DDR_CS0_BNDS 0x0000000f
-#define CFG_DDR_CS0_CONFIG 0x80010102
-#define CFG_DDR_TIMING_0 0x00260802
-#define CFG_DDR_TIMING_1 0x3935D322
-#define CFG_DDR_TIMING_2 0x14904CC8
-#define CFG_DDR_MODE 0x00480432
-#define CFG_DDR_INTERVAL 0x030C0100
-#define CFG_DDR_CONFIG_2 0x04400000
-#define CFG_DDR_CONFIG 0xC3008000
-#define CFG_DDR_CLK_CONTROL 0x03800000
-#define CFG_SDRAM_SIZE 256 /* in Megs */
-
-#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for DDR setup*/
-#define SPD_EEPROM_ADDRESS 0x50 /* DDR DIMM */
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x3935D322
+#define CONFIG_SYS_DDR_TIMING_2 0x14904CC8
+#define CONFIG_SYS_DDR_MODE 0x00480432
+#define CONFIG_SYS_DDR_INTERVAL 0x030C0100
+#define CONFIG_SYS_DDR_CONFIG_2 0x04400000
+#define CONFIG_SYS_DDR_CONFIG 0xC3008000
+#define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000
+#define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */
/*
- * Flash on the Local Bus
- */
-/*
* Flash on the LocalBus
*/
-#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
-
-#define CFG_FLASH0 0xFE000000
-#define CFG_FLASH1 0xFC000000
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
-
-#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */
-#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */
-
-#define CFG_BR0_PRELIM 0xfe001001 /* port size 16bit */
-#define CFG_OR0_PRELIM 0xfe000ff7 /* 32MB Flash */
-#define CFG_BR1_PRELIM 0xfc001001 /* port size 16bit */
-#define CFG_OR1_PRELIM 0xfe000ff7 /* 32MB Flash */
-
-#define CFG_FLASH_CFI /* flash is CFI compat. */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
-
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
+
+#define CONFIG_SYS_FLASH0 0xFE000000
+#define CONFIG_SYS_FLASH1 0xFC000000
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
+
+#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */
+
+#define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */
+#define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */
+#define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */
+
+#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
+#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data*/
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */
+
+/* FPGA and NAND */
+#define CONFIG_SYS_FPGA_BASE 0xc0000000
+#define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
+#define CONFIG_SYS_HMI_BASE 0xc0010000
+#define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */
+#define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */
+
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70)
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_CMD_NAND
+
+/* LIME GDC */
+#define CONFIG_SYS_LIME_BASE 0xc8000000
+#define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */
+#define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */
+#define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */
+
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MB862xx
+#define CONFIG_VIDEO_MB862xx_ACCEL
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define VIDEO_FB_16BPP_PIXEL_SWAP
+#define VIDEO_FB_16BPP_WORD_SWAP
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */
+
+/* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */
+#define CONFIG_SYS_MB862xx_CCF 0x10000
+/* SDRAM parameter */
+#define CONFIG_SYS_MB862xx_MMR 0x4157BA63
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
/* I2C RTC */
#define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x32 /* at address 0x32 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */
-/* RapidIO MMU */
-#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+/* I2C W83782G HW-Monitoring IC */
+#define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */
+
+/* I2C temp sensor */
+/* Socrates uses Maxim's DS75, which is compatible with LM75 */
+#define CONFIG_DTT_LM75 1
+#define CONFIG_DTT_SENSORS {4} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 125
+#define CONFIG_SYS_DTT_LOW_TEMP -55
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
/*
* General PCI
* Memory space is mapped 1-1.
*/
-#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */
-
+#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xE2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x01000000 /* 16M */
+/* PCI is clocked by the external source at 33 MHz */
+#define CONFIG_PCI_CLK_FREQ 33000000
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_BASE 0xE2000000
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
#if defined(CONFIG_PCI)
-
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#define CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
#endif /* CONFIG_PCI */
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_TIMESTAMP /* Print image info with ts */
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_BMP
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
-#undef CONFIG_CMD_DTT
+#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
+#undef CONFIG_CMD_NFS
#define CONFIG_CMD_PING
-#undef CONFIG_CMD_RTC
#define CONFIG_CMD_SNTP
-
+#define CONFIG_CMD_USB
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Internal Definitions
#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+#define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
+ "echo Welcome on the ABB Socrates Board;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootfile=$hostname/uImage\0" \
"netdev=eth0\0" \
"consdev=ttyS0\0" \
- "hostname=socrates\0" \
+ "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \
+ "bootfile=/home/tftp/syscon3/uImage\0" \
+ "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \
+ "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \
+ "uboot_addr=FFFA0000\0" \
+ "kernel_addr=FE000000\0" \
+ "fdt_addr=FE1E0000\0" \
+ "ramdisk_addr=FE200000\0" \
+ "fdt_addr_r=B00000\0" \
+ "kernel_addr_r=200000\0" \
+ "ramdisk_addr_r=400000\0" \
+ "rootpath=/opt/eldk/ppc_85xxDP\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addcons=setenv bootargs $bootargs " \
+ "console=$consdev,$baudrate\0" \
"addip=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask" \
":$hostname:$netdev:off panic=1\0" \
- "addcons=setenv bootargs $bootargs " \
- "console=$consdev,$baudrate\0" \
- "flash_self=run ramargs addip addcons;" \
+ "boot_nor=run ramargs addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
"tftp ${fdt_addr_r} ${fdt_file}; " \
"run nfsargs addip addcons;" \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "fdt_file=$hostname/socrates.dtb\0" \
- "fdt_addr_r=B00000\0" \
- "fdt_addr=FC1E0000\0" \
- "rootpath=/opt/eldk/ppc_85xx\0" \
- "kernel_addr=FC000000\0" \
- "kernel_addr_r=200000\0" \
- "ramdisk_addr=FC200000\0" \
- "ramdisk_addr_r=400000\0" \
- "load=tftp 100000 $hostname/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
+ "update_uboot=tftp 100000 ${uboot_file};" \
+ "protect off fffa0000 ffffffff;" \
+ "era fffa0000 ffffffff;" \
+ "cp.b 100000 fffa0000 ${filesize};" \
"setenv filesize;saveenv\0" \
- "upd=run load update\0" \
+ "update_kernel=tftp 100000 ${bootfile};" \
+ "era fe000000 fe1dffff;" \
+ "cp.b 100000 fe000000 ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "update_fdt=tftp 100000 ${fdt_file};" \
+ "era fe1e0000 fe1fffff;" \
+ "cp.b 100000 fe1e0000 ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "update_initrd=tftp 100000 ${initrd_file};" \
+ "era fe200000 fe9fffff;" \
+ "cp.b 100000 fe200000 ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "clean_data=era fea00000 fff5ffff\0" \
+ "usbargs=setenv bootargs root=/dev/sda1 rw\0" \
+ "load_usb=usb start;" \
+ "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \
+ "boot_usb=run load_usb usbargs addcons;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr};" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
+#define CONFIG_BOOTCOMMAND "run boot_nor"
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
+/* USB support */
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_PCI_OHCI 1
+#define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */
+#define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2)
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
+#define CONFIG_DOS_PARTITION 1
+#define CONFIG_USB_STORAGE 1
+
#endif /* __CONFIG_H */