#ifndef __CONFIG_H
#define __CONFIG_H
-/* High Level Configuration Options */
-#define CONFIG_SOCRATES 1
-
/*
* Only possible on E500 Version 2 or newer cores.
*/
-#define CONFIG_ENABLE_36BIT_PHYS 1
/*
* sysclk for MPC85xx
* in the README.mpc85xxads.
*/
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ 66666666
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
+#define CFG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#undef CFG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_CCSRBAR 0xE0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+#define CFG_SYS_CCSRBAR 0xE0000000
+#define CFG_SYS_CCSRBAR_PHYS_LOW CFG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
-#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
/* Hardcoded values, to use instead of SPD */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x3935D322
-#define CONFIG_SYS_DDR_TIMING_2 0x14904CC8
-#define CONFIG_SYS_DDR_MODE 0x00480432
-#define CONFIG_SYS_DDR_INTERVAL 0x030C0100
-#define CONFIG_SYS_DDR_CONFIG_2 0x04400000
-#define CONFIG_SYS_DDR_CONFIG 0xC3008000
-#define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000
-#define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */
+#define CFG_SYS_DDR_CS0_BNDS 0x0000000f
+#define CFG_SYS_DDR_CS0_CONFIG 0x80010102
+#define CFG_SYS_DDR_TIMING_0 0x00260802
+#define CFG_SYS_DDR_TIMING_1 0x3935D322
+#define CFG_SYS_DDR_TIMING_2 0x14904CC8
+#define CFG_SYS_DDR_MODE 0x00480432
+#define CFG_SYS_DDR_INTERVAL 0x030C0100
+#define CFG_SYS_DDR_CONFIG_2 0x04400000
+#define CFG_SYS_DDR_CONFIG 0xC3008000
+#define CFG_SYS_DDR_CLK_CONTROL 0x03800000
+#define CFG_SYS_SDRAM_SIZE 256 /* in Megs */
/*
* Flash on the LocalBus
*/
-#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
+#define CFG_SYS_FLASH0 0xFE000000
+#define CFG_SYS_FLASH1 0xFC000000
+#define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH1, CFG_SYS_FLASH0 }
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_FLASH0 0xFE000000
-#define CONFIG_SYS_FLASH1 0xFC000000
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
+#define CFG_SYS_LBC_FLASH_BASE CFG_SYS_FLASH1 /* Localbus flash start */
+#define CFG_SYS_FLASH_BASE CFG_SYS_LBC_FLASH_BASE /* start of FLASH */
-#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */
+#define CFG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
-#define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */
-#define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */
-#define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */
-#define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */
+#define CFG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */
+#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* FPGA and NAND */
-#define CONFIG_SYS_FPGA_BASE 0xc0000000
-#define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
-#define CONFIG_SYS_HMI_BASE 0xc0010000
-#define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */
-#define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */
+#define CFG_SYS_FPGA_BASE 0xc0000000
+#define CFG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
-#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70)
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CFG_SYS_NAND_BASE (CFG_SYS_FPGA_BASE + 0x70)
/* LIME GDC */
-#define CONFIG_SYS_LIME_BASE 0xc8000000
-#define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */
-#define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */
-#define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
+#define CFG_SYS_LIME_BASE 0xc8000000
/*
* General PCI
* Memory space is mapped 1-1.
*/
-/* PCI is clocked by the external source at 33 MHz */
-#define CONFIG_PCI_CLK_FREQ 33000000
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE 0xE2000000
-#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 1
-
-#define TSEC1_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC3_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0,1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_TIMESTAMP /* Print image info with ts */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CFG_SYS_PCI1_MEM_PHYS 0x80000000
+#define CFG_SYS_PCI1_IO_PHYS 0xE2000000
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
-#endif
+#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consdev=ttyS0\0" \
"uboot_file=/home/tftp/syscon3/u-boot.bin\0" \
"era fe000000 fe1dffff;" \
"cp.b 100000 fe000000 ${filesize};" \
"setenv filesize;saveenv\0" \
- "update_fdt=tftp 100000 ${fdt_file};" \
+ "update_fdt=tftp 100000 ${fdt_file};" \
"era fe1e0000 fe1fffff;" \
"cp.b 100000 fe1e0000 ${filesize};" \
"setenv filesize;saveenv\0" \
- "update_initrd=tftp 100000 ${initrd_file};" \
+ "update_initrd=tftp 100000 ${initrd_file};" \
"era fe200000 fe9fffff;" \
"cp.b 100000 fe200000 ${filesize};" \
"setenv filesize;saveenv\0" \
"clean_data=era fea00000 fff5ffff\0" \
- "usbargs=setenv bootargs root=/dev/sda1 rw\0" \
- "load_usb=usb start;" \
+ "usbargs=setenv bootargs root=/dev/sda1 rw\0" \
+ "load_usb=usb start;" \
"ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \
"boot_usb=run load_usb usbargs addcons;" \
"bootm ${kernel_addr_r} - ${fdt_addr};" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
""
-#define CONFIG_BOOTCOMMAND "run boot_nor"
/* pass open firmware flat tree */
-/* USB support */
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_PCI_OHCI 1
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
-#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff