#include <asm/arch/base_addr_ac5.h>
-#define CONFIG_BOARD_EARLY_INIT_F
-
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FAT_WRITE
-
#define CONFIG_HW_WATCHDOG
-/* U-Boot Commands */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_EXT4_WRITE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_GPIO
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_MEMTEST
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_TIME
-
/* Memory configurations */
#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on SR1500 */
/* Booting Linux */
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_BOOTARGS "console=ttyS0" __stringify(CONFIG_BAUDRATE)
-#define CONFIG_BOOTCOMMAND "run mmcload; run mmcboot"
#define CONFIG_LOADADDR 0x01000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */
/* Ethernet on SoC (EMAC) */
#define CONFIG_PHY_INTERFACE_MODE PHY_INTERFACE_MODE_RGMII
#define CONFIG_PHY_MARVELL
#define PHY_ANEG_TIMEOUT 8000
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "verify=n\0" \
- "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
- "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
- "bootm ${loadaddr} - ${fdt_addr}\0" \
- "bootimage=zImage\0" \
- "fdt_addr=100\0" \
- "fdtimage=socfpga.dtb\0" \
- "fsloadcmd=ext2load\0" \
- "bootm ${loadaddr} - ${fdt_addr}\0" \
- "mmcroot=/dev/mmcblk0p2\0" \
- "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
- " root=${mmcroot} rw rootwait;" \
- "bootz ${loadaddr} - ${fdt_addr}\0" \
- "mmcload=mmc rescan;" \
- "load mmc 0:1 ${loadaddr} ${bootimage};" \
- "load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
- "qspiroot=/dev/mtdblock0\0" \
- "qspirootfstype=jffs2\0" \
- "qspiboot=setenv bootargs " CONFIG_BOOTARGS \
- " root=${qspiroot} rw rootfstype=${qspirootfstype};"\
- "bootm ${loadaddr} - ${fdt_addr}\0"
-
/* Environment */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
/* Enable SPI NOR flash reset, needed for SPI booting */
#define CONFIG_SPI_N25Q256A_RESET
/*
* Bootcounter
*/
-#define CONFIG_BOOTCOUNT_LIMIT
/* last 2 lwords in OCRAM */
#define CONFIG_SYS_BOOTCOUNT_ADDR 0xfffffff8
#define CONFIG_SYS_BOOTCOUNT_BE
-/* The rest of the configuration is shared */
-#include <configs/socfpga_common.h>
-
-/* U-Boot payload is stored at offset 0x60000 */
-#undef CONFIG_SYS_SPI_U_BOOT_OFFS
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x60000
-
/* Environment setting for SPI flash */
-#undef CONFIG_ENV_SIZE
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#define CONFIG_ENV_SIZE (16 * 1024)
-#define CONFIG_ENV_OFFSET 0x00040000
+#define CONFIG_ENV_OFFSET 0x000e0000
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MODE SPI_MODE_3
-#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SPI_MAX_HZ 100000000 /* Use max of 100MHz */
+#define CONFIG_SF_DEFAULT_SPEED 100000000
+
+/*
+ * The QSPI NOR flash layout on SR1500:
+ *
+ * 0000.0000 - 0003.ffff: SPL (4 times)
+ * 0004.0000 - 000d.ffff: U-Boot
+ * 000e.0000 - 000e.ffff: env1
+ * 000f.0000 - 000f.ffff: env2
+ */
+
+/* The rest of the configuration is shared */
+#include <configs/socfpga_common.h>
#endif /* __CONFIG_SOCFPGA_SR1500_H__ */