/* Virtual target or real hardware */
#undef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_ARMV7
#define CONFIG_SYS_THUMB_BUILD
-#define CONFIG_SOCFPGA
-
/*
* High level configuration
*/
#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_BOARDINFO_LATE
#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_SYS_NO_FLASH
#define CONFIG_CLOCKS
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
-#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100)
+#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - CONFIG_SYS_SPL_MALLOC_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
+ * EPCS/EPCQx1 Serial Flash Controller
+ */
+#ifdef CONFIG_ALTERA_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+/*
+ * The base address is configurable in QSys, each board must specify the
+ * base address based on it's particular FPGA configuration. Please note
+ * that the address here is incremented by 0x400 from the Base address
+ * selected in QSys, since the SPI registers are at offset +0x400.
+ * #define CONFIG_SYS_SPI_BASE 0xff240400
+ */
+#endif
+
+/*
* Ethernet on SoC (EMAC)
*/
#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET)
-#define CONFIG_DESIGNWARE_ETH
-#define CONFIG_NET_MULTI
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_MII
#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ)
#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
-#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 12000
+#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 30000
#endif
/*
#endif
/*
+ * I2C support
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DW
+#define CONFIG_SYS_I2C_BUS_MAX 4
+#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
+#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
+#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
+#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
+/* Using standard mode which the speed up to 100Kb/s */
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SPEED1 100000
+#define CONFIG_SYS_I2C_SPEED2 100000
+#define CONFIG_SYS_I2C_SPEED3 100000
+/* Address of device when used as slave */
+#define CONFIG_SYS_I2C_SLAVE 0x02
+#define CONFIG_SYS_I2C_SLAVE1 0x02
+#define CONFIG_SYS_I2C_SLAVE2 0x02
+#define CONFIG_SYS_I2C_SLAVE3 0x02
+#ifndef __ASSEMBLY__
+/* Clock supplied to I2C controller in unit of MHz */
+unsigned int cm_get_l4_sp_clk_hz(void);
+#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
+#endif
+#define CONFIG_CMD_I2C
+
+/*
+ * QSPI support
+ */
+#ifdef CONFIG_OF_CONTROL /* QSPI is controlled via DT */
+#define CONFIG_CADENCE_QSPI
+/* Enable multiple SPI NOR flash manufacturers */
+#define CONFIG_SPI_FLASH_STMICRO /* Micron/Numonyx flash */
+#define CONFIG_SPI_FLASH_SPANSION /* Spansion flash */
+#define CONFIG_SPI_FLASH_MTD
+/* QSPI reference clock */
+#ifndef __ASSEMBLY__
+unsigned int cm_get_qspi_controller_clk_hz(void);
+#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
+#endif
+#define CONFIG_CQSPI_DECODER 0
+#define CONFIG_CMD_SF
+#endif
+
+#ifdef CONFIG_OF_CONTROL /* DW SPI is controlled via DT */
+#define CONFIG_DESIGNWARE_SPI
+#define CONFIG_CMD_SPI
+#endif
+
+/*
* Serial Driver
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SYS_SPL_MALLOC_START CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_SPL_MALLOC_SIZE (5 * 1024)
+#define CONFIG_SPL_MAX_SIZE (64 * 1024)
#define CHUNKSZ_CRC32 (1 * 1024) /* FIXME: ewww */
#define CONFIG_CRC32_VERIFY
/* Linker script for SPL */
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-socfpga/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
+/*
+ * Stack setup
+ */
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_PARTITIONS
#endif