* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
#define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */
-#define CONFIG_S5PC1XX 1 /* which is in a S5PC1XX Family */
+#define CONFIG_S5P 1 /* which is in a S5P Family */
#define CONFIG_S5PC100 1 /* which is in a S5PC100 */
#define CONFIG_SMDKC100 1 /* working with SMDKC100 */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
/* input clock of PLL: SMDKC100 has 12MHz input clock */
#define CONFIG_SYS_CLK_FREQ 12000000
* 1MB = 0x100000, 0x100000 = 1024 * 1024
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20))
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes for */
- /* initial data */
/*
* select serial console configuration
*/
#define CONFIG_SERIAL0 1 /* use SERIAL 0 on SMDKC100 */
-#define CONFIG_SERIAL_MULTI 1
+
+/* PWM */
+#define CONFIG_PWM 1
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_NAND
-#undef CONFIG_CMD_NET
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_REGINFO
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "SMDKC100 # "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */
#define CONFIG_SYS_HZ 1000
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (256 << 10) /* 256 KiB */
-
/* SMDKC100 has 1 banks of DRAM, we use only one in U-Boot */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE /* SDRAM Bank #1 */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* 256 KiB */
#define CONFIG_IDENT_STRING " for SMDKC100"
-#if !defined(CONFIG_NAND_SPL) && (TEXT_BASE >= 0xc0000000)
+#if !defined(CONFIG_NAND_SPL) && (CONFIG_SYS_TEXT_BASE >= 0xc0000000)
#define CONFIG_ENABLE_MMU
#endif
#define CONFIG_DOS_PARTITION 1
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
+
+/*
+ * Ethernet Contoller driver
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SMC911X 1 /* we have a SMC9115 on-board */
+#define CONFIG_SMC911X_16_BIT 1 /* SMC911X_16_BIT Mode */
+#define CONFIG_SMC911X_BASE 0x98800300 /* SMC911X Drive Base */
+#define CONFIG_ENV_SROM_BANK 3 /* Select SROM Bank-3 for Ethernet*/
+#endif /* CONFIG_CMD_NET */
+
#endif /* __CONFIG_H */