+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* DENX Software Engineering GmbH
*
* Configuation settings for the smartweb.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
* program. Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
-#define CONFIG_SYS_TEXT_BASE 0x23000000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */
#define CONFIG_INITRD_TAG /* pass initrd param to kernel */
#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY /* U-Boot is loaded by a bootloader */
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
-#define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 32
/* setting board specific options */
#define CONFIG_MACH_TYPE MACH_TYPE_SMARTWEB
-#define CONFIG_AUTO_COMPLETE
#define CONFIG_ENV_OVERWRITE 1 /* Overwrite ethaddr / serial# */
-#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_AUTOLOAD "yes"
#define CONFIG_RESET_TO_RETRY
* SDRAM: 1 bank, 64 MB, base address 0x20000000
* Already initialized before u-boot gets started.
*/
-#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE (64 * SZ_1M)
ROUND(3 * CONFIG_ENV_SIZE + (4 * SZ_1M), 0x1000)
/* NAND flash settings */
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE
-#define MTDIDS_NAME_STR "atmel_nand"
-#define MTDIDS_DEFAULT "nand0=" MTDIDS_NAME_STR
-#define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \
- "128k(Bootstrap)," \
- "896k(U-Boot)," \
- "512k(ENV0)," \
- "512k(ENV1)," \
- "4M(Linux)," \
- "-(Root-FS)"
-
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO /* enable the GPIO features */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
-#define CONFIG_BAUDRATE 115200
/*
* Ethernet configuration
*
*/
#define CONFIG_MACB
-#define CONFIG_PHYLIB
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_RMII /* use reduced MII inteface */
#define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */
#define CONFIG_AT91_WANTS_COMMON_PHY
/* BOOTP and DHCP options */
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_NFSBOOTCOMMAND \
"setenv autoload yes; setenv autoboot yes; " \
"setenv bootargs ${basicargs} ${mtdparts} " \
"root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; " \
"dhcp"
-/* Enable the watchdog */
-#define CONFIG_AT91SAM9_WATCHDOG
-#if !defined(CONFIG_SPL_BUILD)
-#define CONFIG_HW_WATCHDOG
-#endif
-#define CONFIG_AT91_HW_WDT_TIMEOUT 15
-
#if !defined(CONFIG_SPL_BUILD)
/* USB configuration */
#define CONFIG_USB_ATMEL
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
/* USB DFU support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
#define CONFIG_USB_GADGET_AT91
/* DFU class support */
-#define CONFIG_USB_FUNCTION_DFU
-#define CONFIG_DFU_NAND
#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_1M
#define DFU_MANIFEST_POLL_TIMEOUT 25000
#endif
/* General Boot Parameter */
#define CONFIG_BOOTCOMMAND "run flashboot"
#define CONFIG_SYS_CBSIZE 512
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
/*
* RAM Memory address where to put the
/*
* The NAND Flash partitions:
*/
-#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET (0x100000)
#define CONFIG_ENV_OFFSET_REDUND (0x180000)
#define CONFIG_ENV_RANGE (SZ_512K)
\
"basicargs=console=ttyS0,115200\0" \
\
- "mtdparts="MTDPARTS_DEFAULT"\0"
-
-/* Command line & features configuration */
-
-#define CONFIG_CMD_NAND
-
-#ifdef CONFIG_MACB
-#else
-#endif /* CONFIG_MACB */
+ "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0"
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x301000
#endif
/* Defines for SPL */
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x0
#define CONFIG_SPL_MAX_SIZE (SZ_4K)
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
-#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_USE_NANDFLASH 1
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SYS_AT91_PLLB 0x10483f0e
#if defined(CONFIG_SPL_BUILD)
-#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF
-#undef CONFIG_SPL_OS_BOOT /* Not supported by existing map */
#endif
#endif /* __CONFIG_H */