#include <asm/arch/omap.h>
-#define CONFIG_DMA_COHERENT
-#define CONFIG_DMA_COHERENT_SIZE (1 << 20)
-
-#define CONFIG_SYS_MALLOC_LEN (16 * 1024 * 1024)
-#ifdef CONFIG_SIEMENS_MACH_TYPE
-#define CONFIG_MACH_TYPE CONFIG_SIEMENS_MACH_TYPE
-#endif
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* commands to include */
-#ifndef CONFIG_SPL_BUILD
#define CONFIG_ROOTPATH "/opt/eldk"
-#endif
-
-#define CONFIG_ENV_OVERWRITE 1
-
-#define CONFIG_SYS_AUTOLOAD "yes"
/* Clock Defines */
#define V_OSCK 24000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
-/* We set the max number of command args high to avoid HUSH bugs. */
-#define CONFIG_SYS_MAXARGS 32
-
/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 1024
-
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* memtest works on 8 MB in DRAM after skipping 32MB from
* start addr of ram disk
*/
-#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */
-
/* Physical Memory Map */
#define PHYS_DRAM_1 0x80000000 /* DRAM Bank #1 */
#define CONFIG_SYS_SDRAM_BASE PHYS_DRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
- GENERATED_GBL_DATA_SIZE)
/* Platform/Board specific defs */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_SERIAL
/* I2C Configuration */
-#define CONFIG_I2C
-#define CONFIG_SYS_I2C
/* Defines for SPL */
-#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
- CONFIG_SPL_TEXT_BASE)
-
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_ECCSTEPS 4
#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
* header. That is 0x800FFFC0--0x80100000 should not be used for any
* other needs.
*/
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
/*
* Since SPL did pll and ddr initialization for us,
* we don't need to do it twice.
*/
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-
-#ifndef CONFIG_SPL_BUILD
-/*
- * USB configuration
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
/* USB DRACO ID as default */
#define CONFIG_USBD_HS
/* USB Device Firmware Update support */
-#define CONFIG_SYS_DFU_DATA_BUF_SIZE (1 << 20)
#define DFU_MANIFEST_POLL_TIMEOUT 25000
-#endif /* CONFIG_SPL_BUILD */
-
/*
* Default to using SPI for environment, etc. We have multiple copies
* of SPL as the ROM will check these locations.
* 0x442000 - 0x800000 : Userland
*/
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
/* UBI Support */
"nand_active_ubi_vol=rootfs_a\0" \
"nand_active_ubi_vol_A=rootfs_a\0" \
"nand_active_ubi_vol_B=rootfs_b\0" \
- "nand_root_fs_type=ubifs rootwait=1\0" \
+ "nand_root_fs_type=ubifs rootwait\0" \
"nand_src_addr=0x280000\0" \
"nand_src_addr_A=0x280000\0" \
"nand_src_addr_B=0x780000\0" \
"nand_active_ubi_vol=rootfs_a\0" \
"rootfs_name=rootfs\0" \
"kernel_name=uImage\0"\
- "nand_root_fs_type=ubifs rootwait=1\0" \
+ "nand_root_fs_type=ubifs rootwait\0" \
"nand_args=run bootargs_defaults;" \
"mtdparts default;" \
"setenv ${partitionset_active} true;" \
/* CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND
devices */
-#if !defined(CONFIG_SPI_BOOT)
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#endif
-#endif
-
-/* Reboot after 60 sec if bootcmd fails */
-#define CONFIG_RESET_TO_RETRY
-#define CONFIG_BOOT_RETRY_TIME 60
#endif /* ! __CONFIG_SIEMENS_AM33X_COMMON_H */